Lexus ES: Vehicle Exterior
Lexus ES (XZ10) Service Manual / Vehicle Exterior
- Door / Hatch
- Front Door
- Front Door Opening Trim Weatherstrip
- Fuel Lid Opener Motor Assembly
- Fuel Lid Opener Switch
- Fuel Lid Opener System (for Gasoline Model)
- Fuel Lid Opener System (for Hv Model)
- Hood
- Hood Lock Control Cable Assembly
- Hood Support
- Kick Sensor
- Luggage Compartment Door
- Luggage Compartment Door Closer Switch
- Luggage Compartment Door Opener Inner Switch
- Luggage Compartment Door Opener Main Switch
- Luggage Compartment Door Opener Outer Switch
- Luggage Compartment Door Opener System (for Gasoline Model)
- Luggage Compartment Door Opener System (for Hv Model)
- Luggage Compartment Door Support
- Luggage Compartment Door Weatherstrip
- Luggage Door Hinge Torsion Bar
- Power Trunk Lid System (for Gasoline Model)
- Power Trunk Lid System (for Hv Model)
- Rear Door
- Rear Door Opening Trim Weatherstrip
- Trunk Lid Actuator
- Exterior Panels / Trim
- Black Out Tape (for Front Door)
- Black Out Tape (for Rear Door)
- Front Bumper
- Front Door Belt Moulding
- Front Door Window Frame Moulding
- Front Pillar Upper Cover
- Grille Shutter
- Grille Shutter System
- Luggage Compartment Door Outside Garnish
- Name Plate
- Quarter Garnish
- Rear Bumper (for Dual Type)
- Rear Bumper (for Single Type)
- Rear Door Belt Moulding
- Rear Door Window Frame Moulding
- Rear Spoiler
- Rear Wheel House Plate
- Rocker Panel Moulding
- Roof Drip Side Finish Moulding
- Windshield Outside Moulding
- Horn
- Lighting (ext)
- Automatic Light Control Sensor
- Hazard Warning Switch
- Headlight Assembly (for Bulb Type Turn Signal Light)
- Headlight Assembly (for Led Type Turn Signal Light)
- Headlight Dimmer Switch
- Headlight Ecu
- Height Control Sensor
- High Mounted Stop Light Assembly
- Illumination Light Assembly (for Front Door)
- Illumination Light Assembly (for Rear Door)
- License Plate Light Assembly
- Lighting System (for Gasoline Model)
- Lighting System (for Hv Model)
- Rear Combination Light Assembly
- Rear Light Assembly
- Relay
- Side Turn Signal Light Assembly
- Stop Light Switch
- Switch Housing
- Mirror (ext)
- Outer Mirror Control Ecu
- Outer Mirror Switch
- Outer Rear View Mirror
- Outer Rear View Mirror Cover
- Outer Rear View Mirror Glass
- Power Mirror Control System (for Gasoline Model With Memory)
- Power Mirror Control System (for Gasoline Model Without Memory)
- Power Mirror Control System (for Hv Model With Memory)
- Power Mirror Control System (for Hv Model Without Memory)
- Sliding Roof / Convertible
- Panoramic Moon Roof System
- Sliding Roof Housing (for Panoramic Moon Roof)
- Sliding Roof Housing(for Moon Roof)
- Sliding Roof Switch Assembly
- Sliding Roof System (for Gasoline Model)
- Sliding Roof System (for Hv Model)
- Vehicle Proximity Notification System
- Vehicle Approaching Speaker (for Front Side)
- Vehicle Approaching Speaker Ecu
- Vehicle Proximity Notification System
- Window / Glass
- Back Window Glass
- Front Passenger Side Power Window Switch
- Power Window Control System (for Gasoline Model)
- Power Window Control System (for Hv Model)
- Power Window Master Switch
- Power Window Regulator Motor (for Front Door)
- Power Window Regulator Motor (for Rear Door)
- Rear Power Window Switch
- Relay
- Window Defogger System (for Gasoline Model)
- Window Defogger System (for Hv Model)
- Window Defogger Wire
- Windshield Deicer System (for Gasoline Model)
- Windshield Deicer System (for Hv Model)
- Windshield Glass
- Wiper / Washer
READ NEXT:
Components
COMPONENTS ILLUSTRATION *A for Driver Side *B for Front Passenger Side *C w/ Illumination - - *1 BOX BOTTOM MAT *2 COURTESY LIGHT ASSEMBLY *3 DOOR ARMREST COVER *
SEE MORE:
Relay
On-vehicle InspectionON-VEHICLE INSPECTION PROCEDURE 1. INSPECT MAIN RELAY (EFI-MAIN NO. 1) (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 3 - 5 Battery voltage not applied between termin
Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 2 FUEL SENDER GAUGE ASSEMBLY (a) Engage the claw to install the No. 2 fuel sender gauge assembly to the fuel tank vent tube assembly. NOTICE: Be careful not to bend the arm of the No. 2 fuel sender gauge assembly. (b) Engage the 2 clamps to connect the wire harn
© 2016-2026 Copyright www.lexguide.net
