Lexus ES: Lighting System (for Gasoline Model)
Lexus ES (XZ10) Service Manual / Vehicle Interior / Lighting (ext) / Lighting System (for Gasoline Model)
- Precaution
- Parts Location
- System Diagram
- How To Proceed With Troubleshooting
- Operation Check
- Customize Parameters
- Initialization
- Problem Symptoms Table
- Terminals Of Ecu
- Dtc Check / Clear
- Freeze Frame Data
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Vehicle Control History
- Light Sensor Circuit (B1244)
- Automatic High Beam System (B124B)
- Automatic High Beam Camera (B124C)
- Headlight Swivel ECU LH Communication (B2410,B2411)
- Headlight Swivel Motor LH (B2412,B2413,B2417,B2418)
- Steering Position Sensor (B2414)
- Vehicle Speed Sensor (B2415)
- Rear Height Control Sensor (B241A)
- Headlight Beam Level Control Motor LH Lost Communication (B2424,B2425)
- Right Headlight ECU Malfunction (B242C,B242D)
- Open in IG Circuit (B242E)
- Open in B Power Line (B242F)
- Headlight LH Circuit (B2439,B243A)
- Left Low Beam Fan Malfunction (B243D,B243E)
- Height Sensor Initialization Incomplete (B2450)
- Variation Code not Written (B2451)
- Abnormal Height Sensor Data at Initialization (B2452)
- Left Headlight ECU Variation Error (B2456)
- Left Headlight ECU Variation Error (B2456)
- Control Module Communication Bus Off (U0073,U0100,U0101,U0126,U0129,U0142,U0155,U0242)
- Control Module Communication Bus OFF (U0073,U0126,U0142,U0182)
- Lost Communication With ECM/PCM "A" (U0100,...,U1117)
- Lost Communication with ECM/PCM "A" Missing Message (U010087,U012587,U012987,U014087)
- Lost Communication with Cruise Control Front Distance Range Sensor Signal Sensor or Center Missing Message (U023587)
- CAN Communication Failure (Message Registry) (U1000)
- Turn Signal Switch Circuit
- Automatic High Beam Switch Indicator does not Come ON
- Automatic High Beam System does not Operate or Operation Indicator does not Illuminate
- Headlight Dimmer Switch Circuit
- Headlight Dimmer Switch Circuit
- Parking Light/Daytime Running Light Circuit
- Hazard Warning Switch Circuit
- Outside Handle Foot Light Circuit
- Front Side Marker Light Circuit
- Taillight Relay Circuit
- Cornering Light Circuit
- High Beam Headlight Circuit
READ NEXT:
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cab
Parts Location
PARTS LOCATION ILLUSTRATION *1 PARK/NEUTRAL POSITION SWITCH ASSEMBLY *2 SIDE TURN SIGNAL LIGHT ASSEMBLY LH *3 SIDE TURN SIGNAL LIGHT ASSEMBLY RH *4 HEADLIGHT ASSEMBLY LH - HEADLIGH
System Diagram
SYSTEM DIAGRAM HEADLIGHT ASSEMBLY CIRCUIT (for LED Type Turn Signal Light) HEADLIGHT ASSEMBLY CIRCUIT (for Bulb Type Turn Signal Light) (for TMC Made) HEADLIGHT ASSEMBLY CIRCUIT (for Bulb
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL LEVEL WARNING SWITCH ASSEMBLY (a) Install the level warning switch assembly as shown in the illustration. *a Protrusion *b Marking Install in this Direction NOTICE: Make sure that the protrusion of the level warning switch is between the 2 mark
CAN Communication Failure (Message Registry) (U1000)
DESCRIPTION The headlight ECU sub-assembly LH or headlight ECU sub-assembly RH stores this DTC if it detects an internal malfunction related to the CAN communication system. for LED Type Turn Signal Light DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from U100
© 2016-2026 Copyright www.lexguide.net
