Lexus ES: Stereo Jack Adapter Light does not Illuminate
DESCRIPTION
Power is supplied to the No. 1 stereo jack adapter assembly illumination from the radio receiver assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
-
When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
-
A communication malfunction DTC may be stored.
-
The radio receiver assembly may not operate normally.
PROCEDURE
1. | CHECK HARNESS AND CONNECTOR (NO. 1 STEREO JACK ADAPTER ASSEMBLY ILLUMINATION POWER SOURCE) |
(a) Disconnect the G103 and G8 No. 1 stereo jack adapter assembly connectors.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage: Tester Connection | Condition | Specified Condition | G103-1 (UPI) - Body ground | Power switch on (ACC) | 5 V | G8-8 (ACC) - Body ground | Power switch on (ACC) | 11 to 14 V | | | *a | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) | | |
NG | | |
2. | CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY) |
(a) Disconnect the G112 radio receiver assembly connector.
(b) Disconnect the G103 No. 1 stereo jack adapter assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection | Condition | Specified Condition | G103-1 (UPI) - G112-1 (USV1) | Always | Below 1 Ω | G103-1 (UPI) or G112-1 (USV1) - Body ground | Always | 10 kΩ or higher | | | *a | Front view of wire harness connector (to Radio Receiver Assembly) | *b | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) | | |
NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK | | |
3. | CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY) |
(a) Disconnect the G6 radio receiver assembly connector.
(b) Disconnect the G8 No. 1 stereo jack adapter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
G8-8 (ACC) - G6-16 (ACC) | Always | Below 1 Ω |
G8-8 (ACC) or G6-16 (ACC) - Body ground | Always | 10 kΩ or higher |
NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ NEXT:
DESCRIPTION Power is supplied to the remote touch (remote operation controller assembly) illumination when the light control switch is in the tail or head position. HINT:
When the remote touch (rem
DESCRIPTION Power is supplied to the remote touch (remote operation controller assembly) illumination when the light control switch is in the tail or head position. WIRING DIAGRAM CAUTION / NOTICE /
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
SEE MORE:
PROBLEM SYMPTOMS TABLE NOTICE:
If the auxiliary battery voltage becomes low, auxiliary battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the windshield deicer system may not operate.
HINT:
Use the table below to hel
SYSTEM DESCRIPTION POWER MIRROR CONTROL SYSTEM (w/o Memory) DESCRIPTION (a) This system has the following functions: electrical remote control mirror function, power retract mirror function, mirror heater function and automatic glare-resistant EC mirror function. FUNCTION OF MAIN COMPONENT Compon
© 2016-2023 Copyright www.lexguide.net
