Lexus ES: Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL NO. 5 ROCKER PANEL MOULDING PROTECTOR
HINT:
When installing the No. 5 rocker panel moulding protector, heat the body rocker panel moulding assembly using a heat light.
Heating Temperature| Item | Temperature |
|---|---|
| Body Rocker Panel Moulding Assembly | 20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
.png)
| *a | Heated Part |
| *b | Heat Light |
NOTICE:
Do not heat the body rocker panel moulding assembly excessively.
(a) Clean the body rocker panel moulding assembly.
(1) Remove any remaining double-sided tape from the body rocker panel moulding assembly.
(2) Wipe off any tape adhesive residue with cleaner.
(b) Using a brush or felt, apply primer or equivalent to the No. 5 rocker panel moulding protector installation area.
NOTICE:
- Use a clean brush or felt.
- Do not touch the body rocker panel moulding assembly until the primer has dried.
(c) Remove the release paper from a new No. 5 rocker panel moulding protector.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
| (d) Install the No. 5 rocker panel moulding protector as shown in the illustration. HINT: Press the No. 5 rocker panel moulding protector firmly to install it. |
|
2. INSTALL NO. 4 ROCKER PANEL MOULDING PROTECTOR
HINT:
When installing the No. 4 rocker panel moulding protector, heat the body rocker panel moulding assembly using a heat light.
Heating Temperature| Item | Temperature |
|---|---|
| Body Rocker Panel Moulding Assembly | 20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
| *a | Heated Part |
| *b | Heat Light |
NOTICE:
Do not heat the body rocker panel moulding assembly excessively.
(a) Clean the body rocker panel moulding assembly.
(1) Using a heat light, heat the body rocker panel moulding assembly surface.
(2) Remove any remaining double-sided tape from the body rocker panel moulding assembly.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Using a brush or felt, apply primer or equivalent to the No. 4 rocker panel moulding protector installation area.
NOTICE:
- Use a clean brush or felt.
- Do not touch the body rocker panel moulding assembly until the primer has dried.
(c) Remove the release paper from a new No. 4 rocker panel moulding protector.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
| (d) Install the No. 4 rocker panel moulding protector. HINT: Press the No. 4 rocker panel moulding protector firmly to install it. |
|
.png)
READ NEXT:
Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL BODY ROCKER PANEL MOULDING ASSEM
Roof Drip Side Finish Moulding
ComponentsCOMPONENTS ILLUSTRATION *1 CENTER ROOF DRIP SIDE FINISH MOULDING *2 NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP ● Non-reusable part - - RemovalREMOVAL CAUTION / NOTI
SEE MORE:
Brake Booster Pump Motor on Time Abnormally Long (C1252,C1253)
DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay. DTC No. Detection Item INF Code DTC
ICS Detection Area Adjustment Incomplete (C1AF0)
DESCRIPTION When ICS detection area adjustment is incomplete, the clearance warning ECU assembly stores DTC C1AF0. DTC No. Detection Item DTC Detection Condition Trouble Area C1AF0 ICS Detection Area Adjustment Incomplete Parking support brake system detection area adjustment incomp
