Lexus ES manuals

Lexus ES: Removal

Lexus ES (XZ10) Service Manual / Vehicle Exterior / Lighting (ext) / Headlight Assembly (for Led Type Turn Signal Light) / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front bumper assembly
  • Measure ultrasonic sensor detection angle
  • Ultrasonic sensor detection angle registration
  • Parking Support Alert System (for HV Model)
  • Parking Support Brake System (for HV Model)

Front television camera view adjustment

Panoramic View Monitor System (for HV Model)

for Initialization

for Calibration

Headlight ECU sub-assembly LH
  • Synchronize the vehicle information
  • Perform headlight ECU sub-assembly LH initialization

Lighting system (for HV Model)

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front bumper assembly
  • Measure ultrasonic sensor detection angle
  • Ultrasonic sensor detection angle registration
  • Parking Support Alert System (for Gasoline Model)
  • Parking Support Brake System (for Gasoline Model)

Front television camera view adjustment

Panoramic View Monitor System (for Gasoline Model)

for Initialization

for Calibration

Headlight ECU sub-assembly LH
  • Synchronize the vehicle information
  • Perform headlight ECU sub-assembly LH initialization

Lighting System (for Gasoline Model)

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT BUMPER ASSEMBLY

Click here

2. REMOVE COWL TOP PANEL INSULATOR

Click here

3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY

Click here

4. REMOVE HEADLIGHT ASSEMBLY

(a) Apply protective tape around the headlight assembly as shown in the illustration.

Protective Tape

(b) Remove the 2 bolts and 3 screws.

*a

Bolt

*b

Screw

(c) Disengage the 2 guides to separate the headlight assembly as shown in the illustration.

Remove in this Direction

(d) Disengage the claw, pull down the connector lock lever as shown in the illustration and disconnect the connector to remove the headlight assembly.

*a

Connector Lock Lever

Disconnect in this Direction

READ NEXT:

 Disassembly

DISASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE HEADLIGHT ECU SUB-ASSEMBLY Click h

 Adjustment

ADJUSTMENT CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTME

 Reassembly

REASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL HEADLIGHT SEAL (for TMC Made) HINT

SEE MORE:

 Parts Location

PARTS LOCATION ILLUSTRATION *A for Manual Tilt and Manual Telescopic Steering Column *B for Power Tilt and Power Telescopic Steering Column *C w/ Power Trunk Lid System - - *1 MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY *2 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-B N

 Jam Protection Function does not Operate

DESCRIPTION This symptom may occur for any of the power windows. The jam protection function operates within a specified range during the manual up or auto up operation. CAUTION / NOTICE / HINT NOTICE: If a power window regulator motor assembly has been replaced with a new one, initialize the pow

© 2016-2026 Copyright www.lexguide.net