Lexus ES: Noise Occurs
PROCEDURE
| 1. | CHECK NOISE CONDITION |
(a) Check from which direction the noise comes (front left or right, or rear left or right).
OK:
The location of the noise source can be determined.
| NG | .gif) | GO TO STEP 3 |
|
.gif)
| 2. | CHECK SPEAKERS |
(a) Check the installation condition of the speaker units that are located near the noise source and that there are no cracks, scratches, deformation or other failures.
| Result | Proceed to |
|---|---|
| No malfunction is found. | A |
| A speaker is installed incorrectly. | B |
| Foreign matter is in a speaker. | C |
| A speaker cone paper is broken. | D |
| A | | GO TO STEP 3 |
| B | | REINSTALL SPEAKER |
| C | | REMOVE FOREIGN MATTER |
| D | | REPLACE SPEAKER |
| 3. | CHECK NOISE CONDITIONS |
(a) Check the noise condition.
HINT:
The radio has a noise prevention function to reduce noise when listening to the radio. If a loud noise occurs, check whether the ground at the antenna mounting base and the noise prevention unit are installed and wired correctly.
| Condition under which Noise Occurs | Noise Source |
|---|---|
| Noise increases when the accelerator pedal is depressed, but stops when the engine is stopped. | Generator |
| Noise occurs during A/C or heater operation. | Blower motor |
| Noise occurs when the horn switch is pressed and released or when pressed and held. | Horn |
| Noise occurs synchronously with the turn signal blinking pattern. | Flasher |
| Noise occurs during window washer operation. | Washer |
| Noise occurs during wiper operation. | Wiper |
| Noise occurs when the brake pedal is depressed. | Stop light switch |
| Others | Static electricity |
HINT:
- In the left column of the table, find the situation that matches the customer's complaint. Then, in the right column, find the part that is causing the noise. Check the respective noise filter.
- To save time and avoid a misdiagnosis, first make sure that the noise is not coming from outside the vehicle.
- Troubleshoot noises in descending order of loudness.
- Setting the radio to a frequency where no signal is received may make recognition of the noise problem easier.
| Result | Proceed to |
|---|---|
| The noise source cannot be determined. | A |
| The noise source can be determined. | B |
| A | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
.gif)
| B | | REPAIR OR REPLACE NOISE SOURCE |
READ NEXT:
Operation Check
OPERATION CHECK REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) SELF CHECK NOTICE:
Before entering self-diagnostic mode, make sure there are no obstructions which may interfere with operation o
Panel Switches do not Function
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
Parts Location
PARTS LOCATION ILLUSTRATION *1 TELEPHONE MICROPHONE ASSEMBLY *2 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-ACC FUSE - ECU-IG1 NO. 4 FUSE - PANEL FUSE - METER-IG2 FUSE - ECU-IG2 NO. 3 FUS
SEE MORE:
Removal
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration)
that must be performed after parts are removed and installed, or replaced during
front disc brake pad removal/installation are shown below.
Necessary Procedures After Parts Remo
Generator Execution Torque Performance (P0E7100)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates that the generator torque execution value does not correspond to the torque command value from the hybrid vehicle control ECU to the generator (MG1). The cause of this malfunction may be one of the following: Area Main Malfunction Descripti
