Lexus ES: Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.
(a) Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
Torque:
5.39 N·m {55 kgf·cm, 48 in·lbf}
HINT:
When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
3. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
Click here .gif)
4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here
5. INSTALL REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY
Click here
6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
7. CONNECT REAR DOOR WEATHERSTRIP
Click here
8. INSTALL REAR DOOR GLASS RUN
Click here
9. INSTALL REAR DOOR PANEL PROTECTOR
Click here
10. INSTALL REAR DOOR NO. 2 VENT SEAL
Click here
11. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER
Click here
12. INSTALL REAR DOOR SERVICE HOLE COVER
Click here
13. INSTALL REAR SIDE CURTAIN ASSEMBLY (w/ Rear Door Sunshade)
Click here
14. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
15. INSTALL COURTESY LIGHT ASSEMBLY
Click here
16. INSTALL REAR DOOR TRIM UPPER PAD
Click here
17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for 2GR-FKS: Click here
for A25A-FXS: Click here
for A25A-FKS: Click here
19. INITIALIZE POWER WINDOW CONTROL SYSTEM
for HV Model: Click here
for Gasoline Model: Click here
20. INSPECT POWER WINDOW OPERATION
for HV Model: Click here
for Gasoline Model: Click here
READ NEXT:
Rear Power Window Switch
ComponentsCOMPONENTS ILLUSTRATION *1 REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY *2 REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL RemovalREMOVAL CA
Relay
On-vehicle InspectionON-VEHICLE INSPECTION PROCEDURE 1. INSPECT DEF RELAY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Cond
SEE MORE:
Inverter Low-voltage Circuit
DESCRIPTION The cause of the malfunction may be the low-voltage circuit. Check whether there is an open circuit in the inverter +B low-voltage power source system or a problem in the communication between the hybrid vehicle control ECU and inverter. Related Parts Check Area Inspection Inver
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Power Trunk Lid System DTC No. Detection Item Link B2205 Kick Sensor Circuit B2222 PBD/PTL Pulse Sensor B2225 PBD/PTL Motor Clutch Malfunction B2250 PBD/PTL Closer Operation B2251 PBD/PTL Closer Switch U0
