Lexus ES manuals

Lexus ES: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.

(a) Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:

5.39 N·m {55 kgf·cm, 48 in·lbf}

HINT:

When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

Click here

4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Click here

5. INSTALL FRONT DOOR PANEL PROTECTOR

Click here

6. INSTALL FRONT DOOR VENT SEAL

Click here

7. INSTALL FRONT DOOR SERVICE HOLE COVER

Click here

8. INSTALL FRONT DOOR TRIM BRACKET

Click here

9. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here

10. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

11. INSTALL COURTESY LIGHT ASSEMBLY

Click here

12. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

13. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

14. INSTALL NO. 2 DOOR TRIM PAD

Click here

15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click here

for A25A-FXS: Click here

for A25A-FKS: Click here

16. INITIALIZE POWER WINDOW CONTROL SYSTEM

for HV Model: Click here

for Gasoline Model: Click here

17. INSPECT POWER WINDOW OPERATION

for HV Model: Click here

for Gasoline Model: Click here

READ NEXT:

 Power Window Regulator Motor (for Rear Door)

 Components

COMPONENTS ILLUSTRATION *1 COURTESY LIGHT ASSEMBLY *2 REAR DOOR TRIM BOARD SUB-ASSEMBLY *3 REAR DOOR TRIM UPPER PAD *4 REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UP

 Removal

REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during pow

SEE MORE:

 Relay

On-vehicle InspectionON-VEHICLE INSPECTION PROCEDURE 1. INSPECT DEF RELAY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 3 - 4 Auxiliary battery voltage applied between terminals 1 and 2

 Crankshaft Position Sensor "A" Circuit Intermittent (P03351F,P03352A,P033531)

DESCRIPTION Refer to DTC P033511. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P03351F Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 second

© 2016-2024 Copyright www.lexguide.net