Lexus ES: Indicator Circuit
DESCRIPTION
The forward recognition camera sends indicator illumination request signals to the combination meter assembly via CAN communication.
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
-
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
.gif)
Sequential Recognition: Click here
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM (CAN BUS CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Can Bus Check.
CAN Bus Check| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed | B |
| B | .gif) | GO TO CAN COMMUNICATION SYSTEM |
|
.gif)
| 2. | CHECK FOR DTCs (HEALTH CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Health Check.
(e) Check for DTCs.
(f) Turn the power switch off.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output. | B |
| B | | GO TO DTC CHART |
|
| 3. | PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Body Electrical > Combination Meter > Active Test| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Multi Display All (White) | Multi-information display (White display) | ON | - |
| Tester Display |
|---|
| Multi Display All (White) |
(f) Turn the power switch off.
| Result | Proceed to |
|---|---|
| The multi-information display turns on according to the operation of the Active Test. | A |
| The multi-information display does not turn on according to the operation of the Active Test. | B |
| B | | REPLACE COMBINATION METER ASSEMBLY |
|
| 4. | READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Lane Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > Lane Control > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| LDA Control | Lane control system control status | Prohibit or Permit | Prohibit: Control prohibited Permit: Control permitted | - |
| Tester Display |
|---|
| LDA Control |
| Result | Proceed to |
|---|---|
| The LTA indicator illuminates and the Data List item LDA Control changes according to the operation of the LTA main switch | A |
| The LTA indicator does not illuminate but the Data List item LDA Control changes according to the operation of the LTA main switch | B |
| The LTA indicator does not illuminate and the Data List item LDA Control does not change according to the operation of the LTA main switch | C |
| A | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B | | REPLACE COMBINATION METER ASSEMBLY |
| C | | REPLACE FORWARD RECOGNITION CAMERA |
READ NEXT:
Components
COMPONENTS ILLUSTRATION *1 COOL AIR INTAKE DUCT SEAL *2 MILLIMETER WAVE RADAR SENSOR ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque - -
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are replaced during millimeter wave radar sensor
SEE MORE:
Drive Motor "A" Execution Torque Performance (P0C1900)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates that the motor torque execution value does not correspond to the torque command value sent from the hybrid vehicle control ECU to the motor (MG2). The cause of this malfunction may be one of the following: Area Main Malfunction Description
Components
COMPONENTS ILLUSTRATION *A w/ Stud Bolt *B w/o Stud Bolt *1 TIMING CHAIN CASE OIL SEAL *2 TIMING CHAIN COVER ASSEMBLY *3 OIL PUMP GASKET - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP Grease Do not apply lubricants to the thr
