Lexus ES: Green Indicator Remains Off
DESCRIPTION
After engine switch on (IG), the DCM (telematics transceiver) will enter into self check mode. The manual (SOS) switch red indicator will illuminate for 2 seconds and turn off followed by the manual (SOS) switch green indicator illuminating and remaining on under normal operation. If neither the red nor green indicators remain on, verification of the subscription should be performed.
PROCEDURE
| 1. | CONFIRM GREEN INDICATOR COMES ON |
(a) After the engine switch is turned on (IG) and the manual (SOS) switch red indicator has come on for 2 seconds, confirm that the manual (SOS) switch green indicator comes on for 2 seconds.
OK:
Green indicator comes on.
| NG | .gif) | GO TO STEP 6 |
|
.gif)
| 2. | CONFIRM SUBSCRIPTION MODE |
(a) Confirm the indicator status 5 seconds after the engine switch is turned on (IG).
| Result | Proceed to |
|---|---|
| Green indicator remains on | A |
| Green indicator remains off | B |
| A | | USE SIMULATION METHOD TO CHECK |
|
| 3. | INPUT VIN WITH TECHSTREAM |
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG) and wait for 10 seconds.
(d) Turn the Techstream on.
(e) Choose "Telematics" from the System Selection Menu, and then click "Utility".
(f) Click "VIN Synchronization" on the Utility Selection Menu.
Click here .gif)
|
| 4. | CONFIRM SUBSCRIPTION MODE |
(a) Confirm the indicator status at 5 seconds after the engine switch is turned on (IG).
| Result | Proceed to |
|---|---|
| Green indicator remains on | A |
| Green indicator remains off | B |
| A | | END |
|
| 5. | REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (telematics transceiver).
Click here
NOTICE:
- The engine switch must be off.
- Do not exchange the DCM (telematics transceiver) with one from another vehicle.
| NEXT | | PERFORM DCM ACTIVATION |
| 6. | CHECK DTC |
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG) and wait for 10 seconds or more.
(d) Turn the Techstream on.
(e) Clear the DTCs.
Body Electrical > Telematics > Clear DTCs(f) Check for DTCs and check that no DTCs are output.
Body Electrical > Telematics > Trouble CodesOK:
No DTCs are output.
| NG | | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
| 7. | REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (telematics transceiver).
Click here
NOTICE:
- The engine switch must be off.
- Do not exchange the DCM (telematics transceiver) with one from another vehicle.
| NEXT | | PERFORM DCM ACTIVATION |
READ NEXT:
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT:
Use the following procedure to troubleshoot the safety connect system.
*: Use the Techstream.
PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP
NEXT
Initialization
INITIALIZATION RESET BACK-UP BATTERY CONDITION HINT: If the back-up battery (mobilephone battery) has been replaced, it is necessary to perform the Reset Backup Battery Condition procedure. (a) Connec
Parts Location
PARTS LOCATION ILLUSTRATION *1 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - DCM FUSE - ECU-IG2 NO. 3 FUSE *2 DLC3 *3 AIRBAG ECU ASSEMBLY *4 DCM (TELEMATICS TRANSCEIVER) - MOBILEPHONE
SEE MORE:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Charging System DTC No. Detection Item Warning Indicate Memory Link P058A01 Auxiliary Battery Monitor Module Range/Performance Charge warning is not displayed DTC stored P162B87 Lost Communication with Battery Monitor Module Missing Messa
Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter
DESCRIPTION The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio receiver assembly via this circuit. WIRING DIAGRAM PROCEDURE 1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY) (a) Disconnect the G5 ra
