Lexus ES: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE BLIND SPOT MONITOR SYSTEM
(a) Customizing with the Techstream
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch to ON.
(3) Turn the blind spot monitor system on.
(4) Turn the Techstream on.
(5) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / Warning.
(6) Select the setting by referring to the table below.
Warning| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| BSM Buzzer Volume Adjust | Sets the volume of the RCTA buzzer (blind spot monitor buzzer). | Medium | 001:Low,011:Medium,101:High | Blind Spot Monitor Sensor LH |
| BSM Mirror Indicator Brightness | Sets the brightness of the indicators in the outer rear view mirror assemblies. | Bright | 001:Dark,101:Bright | Blind Spot Monitor Sensor RH |
| RCTA Function | Switches the RCTA function on and off.* | ON | 0:ON,1:OFF | Blind Spot Monitor Sensor RH |
- *: If the RCTA function is turned off, the RCTAB function of the intelligent clearance sonar system also turns off.
(b) Customizing with multi information display
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(1) Turn the engine switch to ON.
(2) Turn the blind spot monitor system on.
(3) Enter the following menus: Settings / Vehicle Settings / BSM
(4) Select the setting by referring to the table below.
Blind Spot Monitor Setting| Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Brightness | Sets the brightness of the indicators in the outer rear view mirror assemblies. | Bright | Dark or Bright | Blind Spot Monitor Sensor LH |
| Sensitivity | Sets the notification timing for vehicles approaching from behind the vehicle. | Middle | Early, Middle, Late or Only Blind Spot | Blind Spot Monitor Sensor RH |
| Volume. | Sets the volume of the RCTA buzzer (blind spot monitor buzzer). | 2 | 3, 2 or 1 | Blind Spot Monitor Sensor RH |
READ NEXT:
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE BLIND SPOT MONITOR SYSTEM (a) Customizing with the Techstream NOTICE:
When the customer requests a change in a function, first make sure that the function can be cust
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa
Diagnosis System
DIAGNOSIS SYSTEM DESCRIPTION (a) Blind spot monitor data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctionin
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door window frame moulding removal/installation are shown below. Necessary Procedure After Parts
D-Seat ECU Vehicle Information Reading/Writing Process Malfunction (B15F8)
DESCRIPTION This DTC is stored when items controlled by the main body ECU (multiplex network body ECU) cannot be customized via the navigation system vehicle customization screen. HINT: The main body ECU (multiplex network body ECU) controls the front power seat control system (w/ Memory) related it
