Lexus ES manuals

Lexus ES: Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE BLIND SPOT MONITOR SYSTEM

(a) Customizing with the Techstream

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch to ON.

(3) Turn the blind spot monitor system on.

(4) Turn the Techstream on.

(5) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / Warning.

(6) Select the setting by referring to the table below.

Warning

Tester Display

Description

Default

Setting

ECU

BSM Buzzer Volume Adjust

Sets the volume of the RCTA buzzer (blind spot monitor buzzer).

Medium

001:Low,011:Medium,101:High

Blind Spot Monitor Sensor LH

BSM Mirror Indicator Brightness

Sets the brightness of the indicators in the outer rear view mirror assemblies.

Bright

001:Dark,101:Bright

Blind Spot Monitor Sensor RH

RCTA Function

Switches the RCTA function on and off.*

ON

0:ON,1:OFF

Blind Spot Monitor Sensor RH

  • *: If the RCTA function is turned off, the RCTAB function of the intelligent clearance sonar system also turns off.

(b) Customizing with multi-information display

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.
BSM

Display

Description

Default

Setting

ECU

BSM

Switches the BSM function on and off.

ON

ON or OFF

Blind Spot Monitor Sensor RH

Vehicle Settings/BSM

Display

Description

Default

Setting

ECU

Brightness

Sets the brightness of the indicators in the outer rear view mirror assemblies.

Bright

Dark or Bright

Blind Spot Monitor Sensor RH

Sensitivity

Sets the notification timing for vehicles approaching from behind the vehicle.

Middle

Early, Middle, Late or Only Blind Spot

Blind Spot Monitor Sensor RH

PKSA or RCTA

Display

Description

Default

Setting

ECU

RCTA

Switches the RCTA function on and off.

ON

ON / OFF

Blind Spot Monitor Sensor RH

Volume

Sets the volume of the RCTA buzzer (blind spot monitor buzzer).

2

3, 2 or 1

Blind Spot Monitor Sensor RH

READ NEXT:

 Data List / Active Test

DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa

 Diagnosis System

DIAGNOSIS SYSTEM DESCRIPTION (a) Blind spot monitor data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctionin

 Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Blind Spot Monitor System DTC No. Detection Item Link C1A45 Vehicle Speed Sensor C1A45 Vehicle Speed Sensor C1A46 Yaw Rate Sensor

SEE MORE:

 Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch

DESCRIPTION The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (driver door) via CAN co

 Components

COMPONENTS ILLUSTRATION *A for TMC Made *B Type A *C Type B - - *1 COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH *2 DRIVE SHAFT BEARING BRACKET *3 ENGINE COVER BRACKET *4 ENGINE OIL LEVEL DIPSTICK GUIDE *5 GENERATOR ASSEMBLY *6 IGNITION COIL ASSEMBLY

© 2016-2023 Copyright www.lexguide.net