Lexus ES manuals

Lexus ES: Brake Warning Light does not Come ON

DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click here

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if CAN communication system DTCs are output.

Click here

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B

B

INSPECT CAN COMMUNICATION SYSTEM

A

2.

PERFORM ACTIVE TEST USING TECHSTREAM (BRAKE WARNING LIGHT / RED (MALFUNCTION))

(a) Select the Active Test on the Techstream.

Click here

Chassis > ABS/VSC/TRAC > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Brake Warning Light

Brake warning light / red (malfunction)

Warning light ON/OFF

Observe combination meter assembly

Chassis > ABS/VSC/TRAC > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Brake Warning Light

Brake warning light / red (malfunction)

ON or OFF

ON: Warning light on

OFF: Warning light off

-

Chassis > ABS/VSC/TRAC > Active Test

Active Test Display

Brake Warning Light

Data List Display

Brake Warning Light

(b) Check the operating condition of the brake warning light / red (malfunction) when operating it using the Techstream.

Result

Proceed to

Brake warning light / red (malfunction) in the Data List does not change using the Active Test.

A

Brake warning light / red (malfunction) in the Data List turns ON/OFF using the Active Test.

B

A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

3.

INSPECT COMBINATION METER ASSEMBLY

(a) Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.

Click here

Body Electrical > Combination Meter > Active Test

Tester Display

Brake Warning

(b) Check the combination meter assembly.

OK:

The brake warning light / red (malfunction) turns on or off in accordance with Techstream operation.

OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

INSPECT METER / GAUGE SYSTEM

READ NEXT:

 Brake Warning Light Remains ON

DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the brake warn

 EPB System Malfunction (C13AF)

DESCRIPTION The skid control ECU (brake booster with master cylinder assembly) is connected to the parking brake ECU (brake actuator assembly) via CAN communication. If an electric parking brake syste

 Reaction Force Pressure Sensor Power Supply Voltage Malfunction (C14B0,...,C14D4)

DESCRIPTION DTC No. Detection Item INF Code DTC Detection Condition Trouble Area MIL Note C14B0 Reaction Force Pressure Sensor Power Supply Voltage Malfunction 201 The supplie

SEE MORE:

 Components

COMPONENTS ILLUSTRATION *1 FUEL PUMP ASSEMBLY *2 FUEL PUMP PROTECTOR *3 NO. 1 FUEL PIPE SUB-ASSEMBLY *4 NO. 2 FUEL TUBE SUB-ASSEMBLY *5 FUEL PUMP LIFTER ASSEMBLY *6 FUEL PUMP LIFTER GUIDE *7 FUEL PUMP SPACER GASKET *8 FUEL TUBE SUB-ASSEMBLY *9 O-RING -

 Removal

REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below. Necessary Procedure After Parts Removed/Insta

© 2016-2024 Copyright www.lexguide.net