Lexus ES: Transmitter ID not Registered (Main) (C2171)
DESCRIPTION
The IDs of each tire pressure warning valve and transmitter are registered to the tire pressure warning ECU and receiver.
When the ECU detects that a transmitter ID code is not registered in the ECU, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C2171 | Transmitter ID not Registered (Main) | Transmitter ID code is not registered. (When an ID code is unregistered for 3 minutes or more) | Tire pressure warning ECU and receiver | - |
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the Techstream and write them down before removal.
-
It is necessary to perform initialization
.gif)
after registration of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
PROCEDURE
| 1. | CONFIRM REGISTRATION CONDITION (REGISTERED ID CODES) |
(a) Turn the power switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
(f) Read the Data List according to the display on the Techstream.
Chassis > Tire Pressure Monitor > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Registered ID 1 Code | Registered ID1 code | min.: 0 max.: FFFFFFF*1 | ID No. registered for transmitter ID1 displayed | - |
| Registered ID 2 Code | Registered ID2 code | min.: 0 max.: FFFFFFF*1 | ID No. registered for transmitter ID2 displayed | - |
| Registered ID 3 Code | Registered ID3 code | min.: 0 max.: FFFFFFF*1 | ID No. registered for transmitter ID3 displayed | - |
| Registered ID 4 Code | Registered ID4 code | min.: 0 max.: FFFFFFF*1 | ID No. registered for transmitter ID4 displayed | - |
HINT:
*1: Displayed only when the ID No. is not registered.
Chassis > Tire Pressure Monitor > Data List| Tester Display |
|---|
| Registered ID 1 Code |
| Registered ID 2 Code |
| Registered ID 3 Code |
| Registered ID 4 Code |
OK:
The registered transmitter ID codes are displayed on the Techstream.
| OK | .gif) | REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER |
|
.gif)
| 2. | PERFORM REGISTRATION (TRANSMITTER ID) |
(a) Perform registration.
Click here
|
| 3. | PERFORM INITIALIZATION |
(a) Perform initialization.
Click here
|
| 4. | CONFIRM TIRE INFLATION PRESSURE (DATA LIST) |
(a) Turn the power switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
(f) Read the Data List according to the display on the Techstream.
Chassis > Tire Pressure Monitor > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge)/ 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
HINT:
- *1: It may take a few minutes until the values are displayed.
- When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
| Tester Display |
|---|
| ID 1 Tire Inflation Pressure |
| ID 2 Tire Inflation Pressure |
| ID 3 Tire Inflation Pressure |
| ID 4 Tire Inflation Pressure |
| Result | Proceed to |
|---|---|
| All tire pressure readings are equal to specified values. | A |
| Tire pressure values are not displayed. | B |
| A | | END |
| B | | REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER |
READ NEXT:
Receiver Error (C2176)
DESCRIPTION Tire pressure warning valve and transmitter signals are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. DTC No. Detection Item DTC Detection
Initialization not Completed (C2177)
DESCRIPTION Initialization is necessary if one of the following occurs:
The tire pressure warning ECU and receiver is replaced.
A tire pressure warning valve and transmitter is replaced.
Tires
Vehicle Speed Information Communication Lost (C2178)
DESCRIPTION The tire pressure warning ECU and receiver receives signals from the combination meter assembly via CAN communication. If a malfunction occurs in this communication line, DTC C2178 is outp
SEE MORE:
Fuel Pump (for High Pressure)
ComponentsCOMPONENTS ILLUSTRATION *1 NO. 1 FUEL PIPE SUB-ASSEMBLY *2 FUEL PUMP ASSEMBLY *3 FUEL TUBE SUB-ASSEMBLY *4 FUEL PUMP LIFTER ASSEMBLY *5 FUEL PUMP FLANGE *6 FUEL PUMP SPACER GASKET *7 O-RING *8 FUEL PUMP PROTECTOR Tightening torque for "Major
Components
COMPONENTS ILLUSTRATION *1 INTAKE VALVE *2 INTAKE VALVE GUIDE BUSH *3 COMPRESSION SPRING *4 EXHAUST VALVE *5 EXHAUST VALVE GUIDE BUSH *6 STUD BOLT *7 SPARK PLUG TUBE *8 VALVE STEM OIL SEAL *9 VALVE SPRING SEAT *10 NO. 1 STRAIGHT SCREW PLUG *11
