Lexus ES: Right Rear Wheel Speed Sensor Circuit Intermittent (C05121F)
DESCRIPTION
Refer to DTC C051212
Click here .gif)
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C05121F | Right Rear Wheel Speed Sensor Circuit Intermittent |
|
|
- *1: The stop light switch assembly is OFF.
- *2: The stop light switch assembly is ON.
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnosis Condition | The Stop light switch assembly is OFF. | - | ○ | ○ | ○ |
| Malfunction Status | The speed sensor signal is excessively noisy. | ○ | - | - | - |
| The calculated change in wheel speed is more than 980 m/s2. | - | ○ | - | - | |
| The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2. | - | - | ○ | - | |
| The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds. | - | - | - | ○ | |
| Detection Time | - | 5 seconds or more. | 5 seconds or more. | 5 seconds or more. | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
DTC Detection Conditions: C05121F| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 5 | Pattern 6 | Pattern 7 | ||
| Diagnosis Condition | The stop light switch assembly is ON. | ○ | ○ | ○ |
| Malfunction Status | The calculated change in wheel speed is more than 980 m/s2. | ○ | - | - |
| The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2. | - | ○ | - | |
| The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds. | - | - | ○ | |
| Detection Time | 20 seconds or more. | 20 seconds or more. | 20 seconds or more. | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
-
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Click here
-
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Click here
-
DTC precaution
Click here
Procedure to clear warning lights (When not clearing DTCs) Procedure
- Repair or replacement.
- Turn the engine switch on (IG).
- Drive the vehicle at 54 km/h (34 mph) or more for 3 seconds or more to clear the warning lights.
PROCEDURE
| 1. | REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH |
(a) Replace the rear axle hub and bearing assembly RH.
Click here
| NEXT |  | END |
READ NEXT:
Right Rear Wheel Speed Sensor Circuit Intermittent (C05121F)
DESCRIPTION Refer to DTC C051212 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C05121F Right Rear Wheel Speed Sensor Circuit Intermittent
The speed senso
Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range (C05201C)
DESCRIPTION The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. When the skid control ECU (brake actuator assembly) detects an abnormal accelerat
Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range (C05202A)
DESCRIPTION The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. The skid control ECU (brake actuator assembly) memorizes the range of the acceler
SEE MORE:
Drive Motor "A" Phase U Current Sensor Circuit Short to Battery (P0BE512,...,P0BED1F)
DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that the current sensor value is abnormal. The cause of this malfunction may be one of the following: Internal inverter malfunction
Inverter with converter assembly internal circuit malfunction
Inverter low-voltage circuit malfunction
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the values or states of
