Lexus ES manuals

Lexus ES: Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected.

System Name

See Procedure

Lane Control System (for Gasoline Model)

Parking Support Brake System (for Gasoline Model)

Parking Assist Monitor System (for Gasoline Model)

Panoramic View Monitor System (for Gasoline Model)

Pre-collision System (for Gasoline Model)

Power Trunk Lid System (for Gasoline Model)

Lighting System (for Gasoline Model)

POINTS TO NOTE WHEN SERVICING

(a) Pay attention to the following points when servicing.

(1) When disconnecting the cable from the negative (-) battery terminal, "!" may appear on the multi-display assembly. In this case, restore the steering angle neutral point.

Click here

(2) Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click here

HINT:

Each adjusted value for the calibration of the panoramic view monitor system will be stored in the parking assist ECU.

(3) A clear image may not be displayed if there is foreign matter such as water drops, snow or mud on the television camera lens. In such a case, wash the lens with a large amount of water and then wipe it with a soft wet cloth. Do not scrub the camera lens as scrubbing may scratch the camera lens and affect the quality of the image.

PRECAUTIONS FOR PANORAMIC VIEW MONITOR SYSTEM

(a) In the following situations, the panoramic view monitor system may not operate correctly:

(1) When driving on icy, slippery or snowy roads

(2) When using tire chains or a spare tire

(3) When a door is not fully closed

(4) When driving on a slope or rough roads

(5) When using tires other than specified

(6) When the suspension of the vehicle has been modified

(b) As the panoramic view monitor system generates the panoramic image by combining images received from the front television camera assembly, rear television camera assembly and side camera assemblies, the following phenomenon may occur:

(1) A three dimensional object may appear tilted

(2) An object above the road surface may appear farther away than it actually is, or may not be displayed at all

(3) A tall object may look as if it is coming out from between 2 combined images

(4) Depending on the brightness of the area surrounding each camera, there may be a significant difference in the brightness of the images that are used to generate the panoramic image.

(c) The image quality at the four corners of the panoramic image may be low as this is where the individual images are combined.

(d) Objects a certain height above the camera assemblies will not be displayed.

(e) Objects extremely close to the vehicle may not be displayed on the panoramic view monitor.

(f) The panoramic image may not be displayed correctly if a front door or the luggage compartment door is open.

(g) The panoramic image may not be displayed correctly if the height or inclination of the vehicle changes due to loading from passengers, luggage, etc.

(h) As the size and shape of the vehicle icon may differ from that of the actual vehicle, the position of an object relative to the vehicle icon may appear different to its actual position.

NOTES FOR EACH TELEVISION CAMERA ASSEMBLY

(a) Notes for each television camera assembly

(1) The panoramic view monitor system may not function properly if subjected to a severe blow by any hard object.

(2) The cover part of the camera is made of resin. If any organic solvent, degreaser, wax or glass coating contacts the cover, immediately wipe it off and wash the cover with water or cracks may develop.

(3) Exposing the camera to a sudden temperature change may affect proper functioning of the camera.

(4) A clear image may not be displayed if there is foreign matter such as water drops, snow or mud on the television camera lens. In such a case, wash the lens with a large amount of water and then wipe it with a soft wet cloth. Do not scrub the camera lens as scrubbing may scratch the camera lens and affect the quality of the image.

(5) When washing the vehicle with a high-pressure washer, do not spray water on the television camera assembly or surrounding area. High-pressure water can damage the camera.

(b) Images may be unclear even in normal conditions if:

(1) The outer mirror switch assembly is operated (noise may occur in the image).

(2) Electrical devices are used in the cabin (noise may occur in the image).

(3) Accessories that generate radio waves have been installed (noise may occur in the image).

(4) The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

(5) The camera lens is dirty with snow, mud, etc.

(6) The lens of a camera is covered with foreign matter.

(7) A strong beam of light, such as a sunbeam or headlight, hits the camera.

(8) It is too dark around the camera (at night, etc.).

(9) The ambient temperature around the camera is either too high or too low.

(10) The vehicle is tilted at a steep angle.

(11) The area around the vehicle is not sufficiently bright.

(12) The television camera assembly lens is scratched.

(13) The television camera assembly lens has drops of water on it or the humidity is high.

(14) When the camera is used under fluorescent lights, sodium lights or mercury lights, etc., the lights and the illuminated area may appear to flicker.

READ NEXT:

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE NOTICE: The following inspection procedure of the panoramic view monitor system is described on the assumption that the audio and visual system*1 or navigation system*2 is no

 System Description

SYSTEM DESCRIPTION GENERAL (a) This system has front, passenger side, driver side and rear television camera assemblies mounted around the vehicle to display around the vehicle on the multi-display as

 System Diagram

SYSTEM DIAGRAM

SEE MORE:

 Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open (P011515)

DESCRIPTION Refer to DTC P011511. Click here HINT: When DTC P011515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected. DTC No. Detection Item

 Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Wiper and Washer System DTC No. Detection Item DTC Output from Link B1245 Lost Communication with Wiper ECU LIN Main Body B1279 Lost Communication with Humidity/Rain Sensor LIN Main Body B1370 ECU Malfunction Windshield wiper m

© 2016-2023 Copyright www.lexguide.net