Lexus ES: Noise Occurs
PROCEDURE
| 1. | CHECK NOISE CONDITION |
(a) Check from which direction the noise comes (front left or right, or rear left or right).
OK:
The location of the noise source can be determined.
| NG | .gif) | GO TO STEP 3 |
|
.gif)
| 2. | CHECK SPEAKERS |
(a) Check the installation conditions of the speaker units that are located near the noise source and that there are no cracks, scratches, deformation or other failures.
| Result | Proceed to |
|---|---|
| No malfunction is found. | A |
| A speaker is installed incorrectly. | B |
| Foreign matter is in a speaker. | C |
| A speaker cone paper is broken. | D |
| B | | REINSTALL SPEAKER |
| C | | REMOVE FOREIGN MATTER |
| D | | REPLACE SPEAKER |
|
| 3. | CHECK NOISE CONDITIONS |
(a) Check the noise condition.
HINT:
The radio has a noise prevention function to reduce noise when listening to the radio. If a loud noise occurs, check whether the ground at the antenna mounting base and the noise prevention unit are installed and wired correctly.
| Condition under which Noise Occurs | Noise Source |
|---|---|
| Noise increases when the accelerator pedal is depressed, but stops when the engine is stopped. | Generator |
| Noise occurs during A/C or heater operation. | Blower motor |
| Noise occurs when the horn switch is pressed and released or when pressed and held. | Horn |
| Noise occurs synchronously with the turn signal blinking pattern. | Flasher |
| Noise occurs during window washer operation. | Washer |
| Noise occurs during wiper operation. | Wiper |
| Noise occurs when the brake pedal is depressed. | Stop light switch |
| Others | Static electricity |
HINT:
- In the left column of the table, find the situation that matches the customer's complaint. Then, in the right column, find the part that is causing the noise. Check the respective noise filter.
- To save time and avoid a misdiagnosis, first make sure that the noise is not coming from outside the vehicle.
- Troubleshoot noises in descending order of loudness.
- Setting the radio to a frequency where no signal is received may make recognition of the noise problem easier.
| Result | Proceed to |
|---|---|
| The noise source cannot be determined. | A |
| The noise source can be determined. | B |
| A | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
.gif)
| B | | REPAIR OR REPLACE NOISE SOURCE |
READ NEXT:
Operation Check
OPERATION CHECK CHECK NAVIGATION SYSTEM NORMAL CONDITION (a) If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not due to a malfunction. Symptom Answer
Panel Switches do not Function
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
Parts Location
PARTS LOCATION ILLUSTRATION *1 TELEPHONE MICROPHONE ASSEMBLY *2 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-ACC FUSE - ECU-IG1 NO. 4 FUSE - ECU-IG2 NO. 3 FUSE (w/ Manual (SOS) Switch) - P
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type) (a) Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration. HINT: Only 2-piece type back window glass stoppers are provided as supply parts. Use 2-piece type stoppers as r
Dcm Operation History
DCM OPERATION HISTORY DCM OPERATION HISTORY HINT:
This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal
