Lexus ES manuals

Lexus ES: GNSS Antenna Circuit Short to Ground (B15C111,B15C113)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone and GPS antenna assembly (for Roof Side) circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B15C111

GNSS Antenna Circuit Short to Ground

Current to the GNSS antenna is lower than the malfunction threshold for 10 seconds or more when the power switch is on (IG)

(Short circuit)

  • DCM (telematics transceiver)
  • Telephone and GPS antenna assembly (for Roof Side)
  • Telephone and GPS antenna cord (antenna cord sub-assembly)
  • Telephone and GPS antenna cord (No. 2 antenna cord sub-assembly)
  • Telephone and GPS antenna cord (No. 3 antenna cord sub-assembly)

B15C113

GNSS Antenna Circuit Open

Current to the GNSS antenna is higher than the malfunction threshold for 10 seconds or more when the power switch is on (IG)

(Open circuit)

  • DCM (telematics transceiver)
  • Telephone and GPS antenna assembly (for Roof Side)
  • Telephone and GPS antenna cord (antenna cord sub-assembly)
  • Telephone and GPS antenna cord (No. 2 antenna cord sub-assembly)
  • Telephone and GPS antenna cord (No. 3 antenna cord sub-assembly)

WIRING DIAGRAM

w/ SXM Function w/o SXM Function

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Safety Connect System.

Click here

PROCEDURE

1.

CHECK DTC

(a) Turn the power switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the power switch on (IG) and wait for 10 seconds or more.

(d) Turn the Techstream on.

(e) Clear the DTCs.

Body Electrical > Telematics > Clear DTCs

(f) Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes

OK:

No DTCs are output.

OK

USE SIMULATION METHOD TO CHECK

NG

2.

INSPECT TELEPHONE AND GPS ANTENNA CORD (ANTENNA CORD SUB-ASSEMBLY)

(a) Disconnect the J*1 or E*2 telephone and GPS antenna cord (antenna cord sub-assembly) connector.

w/ SXM Function

*a

Component without harness connected (Telephone and GPS Antenna Cord (Antenna Cord Sub-assembly))

w/o SXM Function

*a

Component without harness connected (Telephone and GPS Antenna Cord (Antenna Cord Sub-assembly))

  • *1: w/ SXM Function
  • *2: w/o SXM Function

(b) Disconnect the B telephone and GPS antenna cord (antenna cord sub-assembly) connector.

*a

Component without harness connected (Telephone and GPS Antenna Cord (Antenna Cord Sub-assembly))

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

w/ SXM Function

Tester Connection

Condition

Specified Condition

J-4 - B-1

Always

Below 1 Ω

J-4 or B-1 - Body ground

Always

10 kΩ or higher

J-4a - B-1a

Always

Below 1 Ω

J-4a or B-1a - Body ground

Always

10 kΩ or higher

w/o SXM Function

Tester Connection

Condition

Specified Condition

E-1 - B-1

Always

Below 1 Ω

E-1 or B-1 - Body ground

Always

10 kΩ or higher

E-1a - B-1a

Always

Below 1 Ω

E-1a or B-1a - Body ground

Always

10 kΩ or higher

NG

REPLACE TELEPHONE AND GPS ANTENNA CORD (ANTENNA CORD SUB-ASSEMBLY)

OK

3.

INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY)

(a) Disconnect the K*1 or F*2 telephone and GPS antenna cord (No. 2 antenna cord sub-assembly) connector.

w/ SXM Function

*a

Component without harness connected (Telephone and GPS Antenna Cord (No. 2 Antenna Cord Sub-assembly))

w/o SXM Function

*a

Component without harness connected (Telephone and GPS Antenna Cord (No. 2 Antenna Cord Sub-assembly))

  • *1: w/ SXM Function
  • *2: w/o SXM Function

(b) Disconnect the G telephone and GPS antenna cord (No. 2 antenna cord sub-assembly) connector.

*a

Component without harness connected (Telephone and GPS Antenna Cord (No. 2 Antenna Cord Sub-assembly))

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

w/ SXM Function

Tester Connection

Condition

Specified Condition

K-4 - G-5

Always

Below 1 Ω

K-4 or G-5 - Body ground

Always

10 kΩ or higher

K-4a - G-5a

Always

Below 1 Ω

K-4a or G-5a - Body ground

Always

10 kΩ or higher

w/o SXM Function

Tester Connection

Condition

Specified Condition

F-1 - G-5

Always

Below 1 Ω

F-1 or G-5 - Body ground

Always

10 kΩ or higher

F-1a - G-5a

Always

Below 1 Ω

F-1a or G-5a - Body ground

Always

10 kΩ or higher

NG

REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY)

OK

4.

INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY)

(a) Disconnect the I telephone and GPS antenna cord (No. 3 antenna cord sub-assembly) connector.

*a

Component without harness connected (Telephone and GPS Antenna Cord (No. 3 Antenna Cord Sub-assembly))

(b) Disconnect the H telephone and GPS antenna cord (No. 3 antenna cord sub-assembly) connector.

*a

Component without harness connected (Telephone and GPS Antenna Cord (No. 3 Antenna Cord Sub-assembly))

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I-2 - H-5

Always

Below 1 Ω

I-2 or H-5 - Body ground

Always

10 kΩ or higher

I-2a - H-5a

Always

Below 1 Ω

I-2a or H-5a - Body ground

Always

10 kΩ or higher

NG

REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY)

OK

5.

REPLACE TELEPHONE AND GPS ANTENNA ASSEMBLY (for Roof Side)

(a) Replace the telephone and GPS antenna assembly (for Roof Side) with a new or known good one and check if the same problem occurs again.

Click here

OK:

The system returns to normal.

OK

END

NG

6.

REPLACE DCM (TELEMATICS TRANSCEIVER)

(a) Replace the DCM (Telematics Transceiver).

Click here

NOTICE:

  • The power switch must be off.
  • Do not swap the DCM (Telematics Transceiver) with one from another vehicle.
NEXT

PERFORM DCM ACTIVATION

READ NEXT:

 Airbag Signal Signal Plausibility Failure (B15C464)

DESCRIPTION If the DCM (telematics transceiver) detects an error in communication between the DCM (telematics transceiver) and the airbag ECU assembly as a result of the DCM (telematics transceiver) s

 Emergency Call Switch Circuit Short to Ground (B15C511,B15C513)

DESCRIPTION If the DCM (telematics transceiver) detects an error in the communication between the DCM (telematics transceiver) and the map light sub-assembly (manual (SOS) switch) as a result of the D

 Telephone Main Antenna Circuit Short to Ground (B15CB11,B15CB13)

DESCRIPTION This DTC is stored when the DCM (telematics transceiver) detects an open or a short in the telephone antenna (main) circuit. DTC No. Detection Item DTC Detection Condition Trouble

SEE MORE:

 Installation

INSTALLATION PROCEDURE 1. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY (a) Engage the claw to install the windshield wiper switch assembly as shown in the illustration. Install in this Direction 2. INSTALL UPPER STEERING COLUMN COVER (a) Engage the claw to install the upper steering column cov

 Dtc Check / Clear

DTC CHECK / CLEAR CHECK FOR DTC (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / (desired system) / Trouble Codes. Body Electrical > Wiper > Trouble Codes Body Electrical > Main Body >

© 2016-2024 Copyright www.lexguide.net