Lexus ES manuals

Lexus ES: Freeze Frame Data

FREEZE FRAME DATA

FREEZE FRAME DATA

HINT:

  • When a DTC is stored, the freeze frame data stores the current vehicle (sensor) state as.
  • The freeze frame data cannot be cleared or updated until the recorded DTCs are cleared.

(a) Using the Techstream, the state of the vehicle (sensors) when the system is operating or when a DTC was stored can be checked.

Chassis > Electric Parking Brake

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Speed Sensor Open

Front speed sensor RH open detection

Normal or Error

Normal

-

FL Speed Sensor Open

Front speed sensor LH open detection

Normal or Error

Normal

-

RR Speed Sensor Open

Rear speed sensor RH open detection

Normal or Error

Normal

-

RL Speed Sensor Open

Rear speed sensor LH open detection

Normal or Error

Normal

-

EFI ECU Communication Open

ECM communication open detection

Normal or Error

Normal

-

Deceleration Sensor Open

Deceleration sensor (airbag ECU assembly) communication open detection

Normal or Error

Normal

-

HV ECU Communication Open

Hybrid vehicle control ECU communication open detection

Normal or Error

Normal

-

Body ECU Communication Open

Main body ECU (multiplex network body ECU) communication open detection

Normal or Error

Normal

-

Brake ECU Communication Open

Skid control ECU (brake booster with master cylinder assembly) communication open detection

Normal or Error

Normal

-

A/C ECU Communication Open

Air conditioning amplifier assembly communication open detection

Normal or Error

Normal

-

Navigation ECU Communication Open

Radio receiver assembly communication open detection

Normal or Error

Normal

-

Stop and Start ECU Communication Open

Engine stop and start ECU communication open detection

Normal or Error

Normal

-

Deceleration Sensor Open (EPB)

Acceleration sensor open detection

Normal or Error

Normal

HINT:

EPB stands for electric parking brake.

FR Wheel Speed

Front wheel speed sensor RH reading

0.0 to 326.4 km/h (0 to 202 mph)

When vehicle is stopped: 0 km/h (0 mph)

When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)

When not normal, front speed sensor RH system and CAN communication may be malfunctioning

FL Wheel Speed

Front wheel speed sensor LH reading

0.0 to 326.4 km/h (0 to 202 mph)

When vehicle is stopped: 0 km/h (0 mph)

When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)

When not normal, front speed sensor LH system and CAN communication may be malfunctioning

RR Wheel Speed

Rear wheel speed sensor RH reading

0.0 to 326.4 km/h (0 to 202 mph)

When vehicle is stopped: 0 km/h (0 mph)

When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)

When not normal, rear speed sensor RH system and CAN communication may be malfunctioning

RL Wheel Speed

Rear wheel speed sensor LH reading

0.0 to 326.4 km/h (0 to 202 mph)

When vehicle is stopped: 0 km/h (0 mph)

When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)

When not normal, rear speed sensor LH system and CAN communication may be malfunctioning

Deceleration Sensor 1

Deceleration sensor (airbag ECU assembly) 1 input signal

-18.300 to 18.318 m/s2

When vehicle is stopped: 0 m/s2

When driving vehicle: Continuously changes

When not normal, deceleration sensor (airbag ECU assembly) system and CAN communication may be malfunctioning

Deceleration Sensor 2

Deceleration sensor (airbag ECU assembly) 2 input signal

-18.300 to 18.318 m/s2

When vehicle is stopped: 0 m/s2

When driving vehicle: Continuously changes

When not normal, deceleration sensor (airbag ECU assembly) system and CAN communication may be malfunctioning

Forward and Rearward G

Deceleration sensor (airbag ECU assembly) input signal

-18.300 to 18.318 m/s2

When vehicle is stopped: 0 m/s2

When driving vehicle: Changes according to increase or decrease in speed

When not normal, deceleration sensor (airbag ECU assembly) system and CAN communication may be malfunctioning

Zero Point of Deceleration Sensor

Deceleration sensor (airbag ECU assembly) zero point

-4.595 to 4.559 m/s2

-

-

Zero Point of Deceleration Sensor 2

Deceleration sensor (airbag ECU assembly) 2 zero point

-4.595 to 4.559 m/s2

-

-

Vehicle Speed

Vehicle speed

0.0 to 326.4 km/h (0.0 to 202.8 mph)

When vehicle is stopped: 0 km/h (0 mph)

When driving vehicle: Changes according to vehicle speed (when vehicle speed is constant, there are no big changes in vehicle speed display)

When not normal, speed sensor system and CAN communication may be malfunctioning

ECU +B1 Voltage

Skid control ECU (brake booster with master cylinder assembly) +B1 voltage

0.00 to 20.00 V

11 to 14 V

-

ECU +B2 Voltage

Skid control ECU (brake booster with master cylinder assembly) +B2 voltage

0.00 to 20.00 V

11 to 14 V

-

RH Actuator Motor +Terminal Voltage

Parking brake motor RH (parking brake actuator assembly RH) positive (+) terminal side voltage

0.00 to 20.00 V

-

-

RH Actuator Motor -Terminal Voltage

Parking brake motor RH (parking brake actuator assembly RH) negative (-) terminal side voltage

0.00 to 20.00 V

-

-

LH Actuator Motor +Terminal Voltage

Parking brake motor LH (parking brake actuator assembly LH) positive (+) terminal side voltage

0.00 to 20.00 V

-

-

LH Actuator Motor -Terminal Voltage

Parking brake motor LH (parking brake actuator assembly LH) negative (-) terminal side voltage

0.00 to 20.00 V

-

-

Stop Light Switch

Stop light switch assembly

OFF or ON

OFF: Brake pedal released

ON: Brake pedal depressed

-

EPB Switch

Electric parking brake switch assembly input

OFF, Lock, Release or Unknown

OFF: Lock switch and release switch are off

Lock: Lock switch on

Release: Release switch on

When not normal, electric parking brake switch assembly release side system may be malfunctioning

HINT:

EPB stands for electric parking brake.

Auto Mode Request

Auto mode request status

OFF or ON

-

-

Shift Position

Position of shift lever

P, N, R, D or Unknown

P: Shift lever in P

N: Shift lever in N

R: Shift lever in R

D: Shift lever in D or S

When not normal, shift position signal system may be malfunctioning

IG Switch

IG power source status

OFF or ON

OFF: IG power source voltage is not input to Parking brake ECU (brake actuator assembly)

ON: IG power source voltage is input to Parking brake ECU (brake actuator assembly)

-

Brake Hold Ready

Brake hold control permission status

OFF or ON

-

-

Brake Hold Control Mode

Brake hold control mode

OFF, ON, Release or EPB

OFF: Brake hold control is not operating

ON: Brake hold control is operating

Release: Brake hold control is released

EPB: Parking brake is locked during brake hold control

HINT:

EPB stands for electric parking brake.

EPB Lock Request

Lock demand status

OFF or ON

OFF: Not requested

ON: Requested

HINT:

EPB stands for electric parking brake.

FR Speed Signal Status

FR speed signal status

Normal or Stuck

Normal

-

FL Speed Signal Status

FL speed signal status

Normal or Stuck

Normal

-

RR Speed Signal Status

RR speed signal status

Normal or Stuck

Normal

-

RL Speed Signal Status

RL speed signal status

Normal or Stuck

Normal

-

RH Actuator Current Status

Parking brake actuator assembly RH monitoring current condition

Valid or Inval

Valid

-

LH Actuator Current Status

Parking brake actuator assembly LH monitoring current condition

Valid or Inval

Valid

-

RH Actuator Nut Stroke

Parking brake actuator assembly RH nut stroke value

0.000 to 8.160 mm (0.000 to 0.321 in.)

-

-

LH Actuator Nut Stroke

Parking brake actuator assembly LH nut stroke value

0.000 to 8.160 mm (0.000 to 0.321 in.)

-

-

RH Actuator Motor Actual Current

Parking brake motor RH (parking brake actuator assembly RH) current value

-5.0362 to 50.5000 A

-

-

RH Actuator Motor Adjustment Current

Parking brake motor RH (parking brake actuator assembly RH) current calibration value

-6.9690 to 6.9140 A

-

-

RH Actuator 0 load Current

Parking brake actuator assembly RH current value with no load

-5.0362 to 50.5000 A

-

-

LH Actuator Motor Actual Current

Parking brake motor LH (parking brake actuator assembly LH) current value

-5.0362 to 50.5000 A

-

-

LH Actuator Motor Adjustment Current

Parking brake motor LH (parking brake actuator assembly LH) current calibration value

-6.9690 to 6.9140 A

-

-

LH Actuator 0 load Current

Parking brake actuator assembly LH current value with no load

-5.0362 to 50.5000 A

-

-

Counter of IG ON After EPB Control Cancel

Number of times the power switch was turned on (IG) after EPB control was canceled

0 to 255 Times

-

HINT:

EPB stands for electric parking brake.

RH Actuator Status

Parking brake actuator assembly RH condition

Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control or Full Release Control

-

-

LH Actuator Status

Parking brake actuator assembly LH condition

Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control or Full Release Control

-

-

RH Actuator Motor Current Differential

Differences in parking brake motor RH (parking brake actuator assembly RH) monitoring current

-1.008 to 0.945 A

-

-

LH Actuator Motor Current Differential

Differences in parking brake motor LH (parking brake actuator assembly LH) monitoring current

-1.008 to 0.945 A

-

-

Detailed Freeze DTC

Number of detailed freeze DTCs

0 to 65535

-

-

RH Actuator Motor Gradient Current

Parking brake motor RH (parking brake actuator assembly RH) current gradient

-5.0362 to 50.5000 A

-

-

LH Actuator Motor Gradient Current

Parking brake motor LH (parking brake actuator assembly LH) current gradient

-5.0362 to 50.5000 A

-

-

RH Actuator Motor Relay1

Parking brake motor relay 1 RH condition

OFF or ON

-

-

RH Actuator Motor Relay2

Parking brake motor relay 2 RH condition

OFF or ON

-

-

RH Actuator Motor Relay3

Parking brake motor relay 3 RH condition

OFF or ON

-

-

RH Actuator Motor Relay4

Parking brake motor relay 4 RH condition

OFF or ON

-

-

LH Actuator Motor Relay1

Parking brake motor relay 1 LH condition

OFF or ON

-

-

LH Actuator Motor Relay2

Parking brake motor relay 2 LH condition

OFF or ON

-

-

LH Actuator Motor Relay3

Parking brake motor relay 3 LH condition

OFF or ON

-

-

LH Actuator Motor Relay4

Parking brake motor relay 4 LH condition

OFF or ON

-

-

RH Actuator Motor Current High

Parking brake motor RH (parking brake actuator assembly RH) overcurrent

OFF or ON

-

-

RH Actuator Motor Driver Operation Status

Parking brake motor RH (parking brake actuator assembly RH) driver status

OK or NG

-

-

LH Actuator Motor Current High

Parking brake motor LH (parking brake actuator assembly LH) overcurrent status

OFF or ON

-

-

LH Actuator Motor Driver Operation Status

Parking brake motor LH (parking brake actuator assembly LH) driver status

OK or NG

-

-

READ NEXT:

 How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. CUSTOMER PROBLEM ANALYSIS (a) Interview the customer and confir

 Message Not Displayed on Multi-information Display When AUTO Function Set to ON/OFF

DESCRIPTION When the AUTO function is set to ON/OFF, a message is displayed on the multi-information display in the combination meter assembly. WIRING DIAGRAM PROCEDURE 1. CHECK OPERATION OF AU

 Parts Location

PARTS LOCATION ILLUSTRATION *1 PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) *2 ECM *3 NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY - EPB NO. 1 FUSE *4 SKID CONTRO

SEE MORE:

 Adjustment

ADJUSTMENT PROCEDURE 1. SECURE VEHICLE (a) Fully apply the parking brake and chock a wheel. CAUTION: Make sure to apply the parking brake and chock a wheel before performing this procedure. If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly r

 Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZE LIGHTING SYSTEM (EXT) NOTICE: When the customer requests a change in a function, first make sure that the function can be customized. Be sure to make a note of the current settings before customizing. When troubleshooting a function, first make sure that the fun

© 2016-2024 Copyright www.lexguide.net