Lexus ES: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
*: Use the Techstream.
PROCEDURE
| 1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. | CUSTOMER PROBLEM ANALYSIS |
(a) Interview the customer and confirm the problem.
Click here .gif)
|
| 3. | INSPECT AUXILIARY BATTERY VOLTAGE |
Standard Voltage:
11 to 14 V
- If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
|
| 4. | CHECK DTC AND FREEZE FRAME DATA* |
(a) Check and record DTCs and freeze frame data.
Chassis > Electric Parking Brake > Trouble Codes(b) Clear the DTCs and freeze frame data.
Chassis > Electric Parking Brake > Clear DTCs(c) Recheck for DTCs.
(1) Reconfirm the DTCs based on the recorded DTCs and freeze frame data.
Chassis > Electric Parking Brake > Trouble Codes(2) Try to reproduce the problem symptoms based on the recorded DTCs and freeze frame data, and then check if the DTCs are output again.
| Result | Proceed to |
|---|---|
| DTCs are not output (Problem symptom occurs.) | A |
| DTCs are output | B |
| DTCs are not output (Problem symptom does not occur.) | C |
HINT:
- Refer to Diagnostic Trouble Code Chart if any DTCs are output.
- When DTCs indicating a CAN communication system malfunction are output, first troubleshoot and repair the CAN communication system.
| B | .gif) | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| C | | USE SIMULATION METHOD TO CHECK |
|
| 5. | PROBLEM SYMPTOMS TABLE |
(a) Proceed to Problem Symptoms Table.
Click here
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
| B | | GO TO STEP 7 |
|
| 6. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Refer to Terminals of ECU.
Click here
(b) Refer to Data List / Active Test.
Click here
|
| 7. | REPAIR OR REPLACE |
|
| 8. | CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Message Not Displayed on Multi-information Display When AUTO Function Set to ON/OFF
DESCRIPTION When the AUTO function is set to ON/OFF, a message is displayed on the multi-information display in the combination meter assembly. WIRING DIAGRAM PROCEDURE 1. CHECK OPERATION OF AU
Parts Location
PARTS LOCATION ILLUSTRATION *1 PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) *2 ECM *3 NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY - EPB NO. 1 FUSE *4 SKID CONTRO
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following s
SEE MORE:
Hybrid/EV Battery Precharge Contactor Circuit Short to Ground (P0AE411)
DESCRIPTION The SMRs (System Main Relays) are the relays that connect or disconnect the high-voltage system in accordance with commands from the hybrid vehicle control ECU. There are 3 SMRs and 1 system main resistor. SMRB, SMRP, SMRG and the system main resistor are located in the HV battery juncti
On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT MASS AIR FLOW METER SUB-ASSEMBLY HINT: Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly. Click here (a) Read the value of Data List item "Mass Air Flow Sensor" using the Techstream. NOTICE: Perform the inspection of
