Lexus ES manuals

Lexus ES: Electric Parking Brake ECU Communication Stop Mode

Lexus ES (XZ10) Service Manual / Power Source & Network / Networking / Can Communication System (for Hv Model) / Electric Parking Brake ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Electric Parking Brake ECU Communication Stop Mode

Any of the following conditions are met:

  • Communication stop for "Electric Parking Brake" is indicated on the "Communication Bus Check" screen of the Techstream.

    Click here

  • Communication stop history for "Electric Parking Brake" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Electric Parking Brake" is 6 or more.)

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Electric Parking Brake ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Brake actuator assembly branch line or connector
  • Power source circuit of brake actuator assembly
  • Brake actuator assembly ground circuit
  • Brake actuator assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the A54 brake actuator assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A54-12 (CANH) - A54-11 (CANL)

Cable disconnected from negative (-) auxiliary battery terminal

54 to 69 Ω

*a

Front view of wire harness connector

(to Brake Actuator Assembly)
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A54-1 (MGND) - Body ground

Cable disconnected from negative (-) auxiliary battery terminal

Below 1 Ω

A54-2 (EGND) - Body ground

Cable disconnected from negative (-) auxiliary battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Brake Actuator Assembly)

(b) Reconnect the cable to the negative (-) auxiliary battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A54-9 (BEPB) - Body ground

Power switch off

11 to 14 V

A54-26 (IG) - Body ground

Power switch on (IG)

11 to 14 V
OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

READ NEXT:

 Headlight ECU LH Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Headlight ECU LH Communication Stop Mode Any of the following conditions are met: Communication stop for "HL AutoLeveling/AFS/AHS" is in

 Headlight ECU RH Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Headlight ECU RH Communication Stop Mode Any of the following conditions are met: Communication stop for "HL AutoLeveling/AFS/AHS (Sub)"

 Center Airbag Sensor Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Center Airbag Sensor Communication Stop Mode Any of the following conditions are met: Communication stop for "Airbag" is indicated on th

SEE MORE:

 Display does not Dim when Light Control Switch is Turned ON

DESCRIPTION When the audio and visual system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line. After AVC-LAN communication

 Torque Sensor Zero Point Adjustment Undone (C1515)

DESCRIPTION This DTC does not indicate a malfunction. The power steering ECU (rack and pinion power steering gear assembly) stores this DTC when it determines that torque sensor zero point calibration has not been performed. When the IG terminal voltage is below 8 V, torque sensor zero point calibra

© 2016-2026 Copyright www.lexguide.net