Lexus ES manuals

Lexus ES: Cellular Phone Registration Failure

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

  • When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio receiver assembly may not operate normally.

PROCEDURE

1.

CHECK USAGE CONDITION

(a) Check that the vehicle and cellular phone meet the following conditions:

NOTICE:

If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.

  • The cellular phone is "Bluetooth" compatible.

    Click here

  • "Bluetooth" setting of the cellular phone is on.
  • Operating system and software of the cellular phone are the latest versions.
  • There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.
  • The "Wi-Fi" setting of the cellular phone is off.
  • The "Wi-Fi" tethering setting of the cellular phone is off.

(b) Register the cellular phone again and check if it is registered correctly.

HINT:

If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

END

B

2.

RESTART CELLULAR PHONE

(a) Restart the cellular phone.

(b) Turn the power switch off.

(c) Turn the power switch on (ACC).

(d) Register the cellular phone as a connected device again and check if it is registered correctly.

HINT:

If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

END

B

3.

BRING CELLULAR PHONE NEAR IN-VEHICLE DEVICE

(a) Place the cellular phone close to the radio receiver assembly.

(b) Register the cellular phone as a connected device again and check if it is registered correctly.

HINT:

If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

END

B

4.

CLEAR REGISTERED DEVICE INFORMATION

(a) Clear all "Bluetooth" devices registered to the cellular phone and the radio receiver assembly.

(b) Register the cellular phone as a connected device again and check if it is registered correctly.

HINT:

If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

END

B

5.

RESTART CELLULAR PHONE

(a) Restart the cellular phone.

(b) Turn the power switch off.

(c) Turn the power switch on (ACC).

(d) Register the cellular phone as a connected device again and check if it is registered correctly.

HINT:

If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

END

B

6.

CHECK USING ANOTHER VEHICLE

(a) Check if the cellular phone can be registered normally to another "Bluetooth" compatible vehicle of the same model.

HINT:

  • Make sure to obtain the customer's permission to perform this procedure.
  • After the inspection, clear the registered information and usage history acquired during the inspection.
  • If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

REPLACE RADIO RECEIVER ASSEMBLY

B

7.

CHECK USING ANOTHER CELLULAR PHONE

(a) Using another "Bluetooth" compatible cellular phone, register the cellular phone and check that it is registered correctly.

HINT:

  • Make sure to obtain the customer's permission to perform this procedure.
  • After the inspection, clear the registered information and usage history acquired during the inspection.
  • If operation of the cellular phone or radio receiver assembly is requested, make sure to follow the instructions closely and perform the operation.

Result

Proceed to

Cellular phone can be registered.

A

Cellular phone cannot be registered.

B

A

END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED)

B

REPLACE RADIO RECEIVER ASSEMBLY

READ NEXT:

 Cursor or Map Rotates when Vehicle Stopped

PROCEDURE 1. CHECK CONDITION (a) Check with the customer if the vehicle has been turned by a turntable. OK: Vehicle has not been turned by a turntable. HINT: If the vehicle is turned on a

 Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZING WITH REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) (a) Customizing with the touch function cancellation function. (w/ Touch Function Cancellation Function) NOTIC

 Data List / Active Test

DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa

SEE MORE:

 Components

COMPONENTS ILLUSTRATION *1 INTAKE VALVE *2 INTAKE VALVE GUIDE BUSH *3 COMPRESSION SPRING *4 EXHAUST VALVE *5 EXHAUST VALVE GUIDE BUSH *6 STUD BOLT *7 SPARK PLUG TUBE *8 VALVE STEM OIL SEAL *9 VALVE SPRING SEAT *10 NO. 1 STRAIGHT SCREW PLUG *11

 Stop Lamp Relay Actuator Stuck On (C13807E)

DESCRIPTION When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights. Illumination Conditions: Pre-collision brake is operating

© 2016-2024 Copyright www.lexguide.net