Lexus ES manuals

Lexus ES: Brake Pressure Control Solenoid "A" Control Circuit Short to Battery (C13C012,...,C13C049)

Lexus ES (XZ10) Service Manual / Brake / Brake Control / Dynamic Control Systems / Electronically Controlled Brake System (for Gasoline Model) / Brake Pressure Control Solenoid "A" Control Circuit Short to Battery (C13C012,...,C13C049)

DESCRIPTION

The ABS solenoid relay and master cylinder cut solenoid valves are built into the brake actuator assembly.

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor.

When this DTC is stored, the fail-safe function operates and the ABS solenoid relay is turned off to prevent the master cylinder cut solenoid valves from operating.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C13C012

Brake Pressure Control Solenoid "A" Control Circuit Short to Battery

A short to +B in the master cylinder cut solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C13C014

Brake Pressure Control Solenoid "A" Control Circuit Short to Ground or Open

An open or short in the master cylinder cut solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C13C01C

Brake Pressure Control Solenoid "A" Control Circuit Voltage Out of Range

  • A current leak in the master cylinder cut solenoid circuit is detected during the self test.
  • The master cylinder cut solenoid valve operation request signal and master cylinder cut solenoid valve operation feedback signal do not match for a certain period of time.

Skid control ECU (brake actuator assembly)

C13C01E

Brake Pressure Control Solenoid "A" Control Circuit Resistance Out of Range

An abnormal resistance in the master cylinder cut solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

C13C049

Brake Pressure Control Solenoid "A" Control Internal Electronic Failure

An internal malfunction in the master cylinder cut solenoid circuit is detected during the self test.

Skid control ECU (brake actuator assembly)

DTC Detection Conditions: C13C014
 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

-

-

-

Malfunction Status

An open in the master cylinder cut solenoid circuit is detected during the self test.

-

A short in the master cylinder cut solenoid circuit is detected during the self test.

-

Detection Time

-

-

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C13C01C
 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

-

-

-

Malfunction Status

A current leak in the master cylinder cut solenoid circuit is detected during the self test.

-

The master cylinder cut solenoid valve operation request signal and master cylinder cut solenoid valve operation feedback signal do not match for a certain period of time.

-

Detection Time

-

-

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click here

PROCEDURE

1.

REPLACE BRAKE ACTUATOR ASSEMBLY

(a) Replace the brake actuator assembly.

Click here

NEXT

END

READ NEXT:

 Brake Pressure Control Solenoid "B" Control Circuit Short to Battery (C13C912,...,C13C949)

DESCRIPTION The ABS solenoid relay and master cylinder cut solenoid valves are built into the brake actuator assembly. Depending on the operating conditions, the master cylinder cut solenoid valves re

 Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range (C14D71C)

DESCRIPTION The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. This DTC is stored when the skid control ECU (brake actuator assembly) receives a

 Left Front Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open (C14E014)

DESCRIPTION Refer to DTC C050012 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C14E014 Left Front Wheel Speed Sensor Supply Voltage Circuit Short to Ground or

SEE MORE:

 Removal

REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE NO. 2 DOOR TRIM PAD Click here 2. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver

 4wd Control Ecu

ComponentsCOMPONENTS ILLUSTRATION *1 NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY *2 4WD ECU ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque - - InstallationINSTALLATION PROCEDURE 1. INSTALL 4WD ECU ASSEMBLY (a) Install the 4WD ECU assembly to the instrument panel rei

© 2016-2024 Copyright www.lexguide.net