Lexus ES manuals

Lexus ES: TRAC does not Operate

DESCRIPTION

When ABS, TRAC or VSC is operating, the skid control ECU (brake booster with master cylinder assembly) blinks the slip indicator light to inform the driver that slippage occurred.

When in VSC off mode, or TRAC and VSC are disabled, the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates to inform the driver.

When a communication malfunction with the hybrid vehicle control ECU is detected, TRAC and VSC are disabled. Also when the system is malfunctioning, TRAC and VSC are disabled and the indicator lights of related systems illuminate.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click here

PROCEDURE

1.

BRAKE PROBLEM CHECK

(a) Check if the slip indicator light was illuminated when TRAC did not operate.

OK:

The slip indicator light was illuminated.

HINT:

When a DTC is stored, the slip indicator light is illuminated and TRAC does not operate due to the fail-safe function.

(b) Check the operation condition of the VSC OFF switch when TRAC did not operate.

OK:

The VSC OFF switch had been operated to turn off TRAC when TRAC did not operate.

HINT:

When the multi-information display in the combination meter assembly displays "Traction Control Turned Off", TRAC does not operate.

OK

END

NG

2.

CHECK DTC

(a) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC > Clear DTCs

(b) Turn the power switch off.

(c) Turn the power switch on (IG).

(d) Check the DTCs (electronically controlled brake system) that are output.

Click here

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

DTCs are not output.

A

Electronically controlled brake system DTCs are output.

B

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

A

3.

CHECK VEHICLE

(a) Operate the VSC OFF switch and check that the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.

OK:

The multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.

NG

INSPECT VSC OFF SWITCH CIRCUIT

OK

4.

PERFORM TEST MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CIRCUIT)

(a) Using the Techstream, perform a Test Mode (Signal Check) inspection sensor check and check that speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.

Click here

Chassis > ABS/VSC/TRAC > Utility

Tester Display

Signal Check

OK:

Speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.

NG

INSPECT AND REPAIR MALFUNCTIONING SPEED SENSOR CIRCUIT

OK

5.

PERFORM OPERATION CHECK DRIVING

(a) Operate the VSC OFF switch and check that the system is not in TRAC off mode or VSC off mode.

(b) Check that no DTCs are output and that each warning light is not illuminated.

(c) Start off the vehicle on a low friction surface and check that TRAC operates when attempting to make the drive wheels slip.

OK:

TRAC operates when slip occurs when starting off.

NOTICE:

  • Even when the system is normal, VSC may not operate when the vehicle speed is low or TRAC may not operate due to a malfunction. Make sure that only the drive wheels slip during the procedure.
  • When confirming that the slip indicator light blinks, do not slip the drive wheels longer than necessary. Whether TRAC operated or not can be checked by reading the Freeze Frame Data when the system operated.
  • Pay attention to your surroundings when performing the procedure and depress the accelerator pedal with caution.
OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

READ NEXT:

 Control Module Communication Bus Off (U0073,U0100,U0110,U0120,U0124,U0126,U0128,U0151,U0293)

DESCRIPTION The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2). The skid control ECU (brake booster with master cylin

 Vehicle Control History

VEHICLE CONTROL HISTORY VEHICLE CONTROL HISTORY HINT: A part of the control history can be confirmed using the vehicle control history. Click here

 VSC does not Operate or VSC does not Operate Correctly

DESCRIPTION When ABS, TRAC or VSC is operating, the skid control ECU (brake booster with master cylinder assembly) blinks the slip indicator light to inform the driver that slippage occurred. When a c

SEE MORE:

 Installation

INSTALLATION PROCEDURE 1. INSTALL CAMSHAFT TIMING GEAR BOLT (a) Make sure that the No. 1 cylinder is at TDC/compression. HINT: Check that the cutout of the camshaft timing gear assembly is at the top and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing chain

 System Description

SYSTEM DESCRIPTION LIN COMMUNICATION SYSTEM DESCRIPTION The LIN communication system is used for communication between the components in the tables below. If communication cannot be performed through LIN communication such as when there is an open or short in a communication line, the master control

© 2016-2024 Copyright www.lexguide.net