Lexus ES: Touch Pad Memory Module Malfunction (B155B)
DESCRIPTION
This DTC is stored if the remote touch (remote operation controller assembly) detects a malfunction in itself, such as internal hardware failure or remote touch screen memory module malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B155B | Touch Pad Memory Module Malfunction | Internal memory module malfunction | Remote touch (remote operation controller assembly) |
PROCEDURE
| 1. | CHECK DTC |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | CHECK INFORMATION CODE |
(a) Check that the part number of the remote touch (remote operation controller assembly) is correct.
| Result | Proceed to |
|---|---|
| The part number of the remote touch (remote operation controller assembly) is correct | A |
| The part number of the remote touch (remote operation controller assembly) is incorrect | B |
| B | | REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) |
|
| 3. | REMOTE TOUCH SELF CHECK (CHECK REMOTE TOUCH SCREEN OPERATION POSITION RECOGNITION CONDITION) |
(a) Enter self-diagnostic mode.
Click here .gif)
(b) Operate the remote touch screen laterally and check that the remote touch screen generates vibration feedback.
NOTICE:
Since the remote touch screen may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate the remote touch screen in self-diagnostic mode.
HINT:
When operating at an excessively low temperature, vibration feedback may be difficult to feel.
| Result | Proceed to |
|---|---|
| Vibration feedback is generated according to remote touch screen operation | A |
| The switch illumination changes but vibration feedback is not generated in accordance to remote touch screen operation | B |
| B | | REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) |
|
| 4. | CHECK DTC |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Turn the engine switch off.
(c) Turn the engine switch on (ACC) and wait for 5 seconds.
(d) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) |
READ NEXT:
AV Signal Stoppage (Low Battery Voltage) (B158F)
DESCRIPTION This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio receiver assembly dropping temporarily. DTC No. Detection Item DTC Detection
Lost Communication with Haptic Device (B1323,B1324,B1326)
DESCRIPTION These DTCs are stored when communication between the radio receiver assembly and remote touch (remote operation controller assembly), combination meter assembly or clock assembly is not po
HD Radio Tuner Malfunction (B1551,B15A0,B15B3,B15B4,B15B7,B15BA,B15F9)
DESCRIPTION These DTCs are stored when a malfunction occurs in the radio receiver assembly. DTC No. Detection Item DTC Detection Condition Trouble Area B1551 HD Radio Tuner Malfunction
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY (a) Coat 2 new transaxle case gaskets with Toyota Genuine ATF WS and install them to the automatic transaxle case sub-assembly. (b) Coat a new transaxle case gasket with Toyota Genuine ATF WS and install it to the counter drive gear
Bleeding
BLEEDING CAUTION / NOTICE / HINT NOTICE:
Move the shift lever to P and apply the parking brake before bleeding the brakes.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
If brake fluid leaks onto any painted surface, immediately was
