Lexus ES: Switch Failure (B2342)
DESCRIPTION
This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly) detects that the panoramic moon roof switch (map light sub-assembly) is stuck for 30 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2342 | Switch Failure | Sliding roof ECU (sliding roof drive gear assembly) detects panoramic moon roof switch (map light sub-assembly) is stuck for 30 seconds or more. |
|
WIRING DIAGRAM
Refer to DTC B2341.
Click here .gif)
CAUTION / NOTICE / HINT
NOTICE:
-
If the sliding roof ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) must be initialized.
Click here
-
The panoramic moon roof system uses the CAN and LIN communication system. First, confirm that there are no malfunctions in the CAN and LIN communication system. Refer to How to Proceed with Troubleshooting.
Click here
- DTC B2342 is stored in the sliding roof ECU (sliding roof drive gear assembly).
PROCEDURE
| 1. | CHECK FOR DTC |
(a) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs(b) Check for DTCs.
Body Electrical > Sliding Roof > Trouble CodesOK:
DTC B2342 is not output.
| OK | .gif) | END (DUE TO SWITCH BEING OPERATED FOR 30 SECONDS OR MORE) |
|
.gif)
| 2. | READ VALUE USING TECHSTREAM (SLIDING ROOF) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Roof > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch Failure(Past) | Sliding roof open switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Close Switch Failure(Past) | Sliding roof close switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) | - |
| Up Switch Failure(Past) | Roof sunshade open switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Down Switch Failure(Past) | Roof sunshade close switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) | - |
| Open Switch Failure(Current) | Sliding roof open switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) | - |
| Close Switch Failure(Current) | Sliding roof close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Up Switch Failure(Current) | Roof sunshade open switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Down Switch Failure(Current) | Roof sunshade close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) | - |
| Tester Display |
|---|
| Open Switch Failure(Past) |
| Close Switch Failure(Past) |
| Up Switch Failure(Past) |
| Down Switch Failure(Past) |
| Open Switch Failure(Current) |
| Close Switch Failure(Current) |
| Up Switch Failure(Current) |
| Down Switch Failure(Current) |
OK:
OFF appears on the Techstream screen.
| OK | | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
|
| 3. | CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (MAP LIGHT SUB-ASSEMBLY)) |
(a) Disconnect the Q1 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the P13 panoramic moon roof switch (map light sub-assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q1-10 (OPN) or P13-11 (OPN) - Body ground | Always | 10 kΩ or higher |
| Q1-8 (CLS) or P13-12 (CLS) - Body ground | Always | 10 kΩ or higher |
| Q1-4 (TILT) or P13-7 (B) - Body ground | Always | 10 kΩ or higher |
| Q1-5 (OPN) or P13-23 (UP) - Body ground | Always | 10 kΩ or higher |
| Q1-9 (CLS) or P13-24 (DOWN) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 4. | INSPECT PANORAMIC MOON ROOF SWITCH (MAP LIGHT SUB-ASSEMBLY) |
(a) Remove the panoramic moon roof switch (map light sub-assembly).
Click here
(b) Inspect the panoramic moon roof switch (map light sub-assembly).
Click here
| OK | | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
| NG | | REPLACE PANORAMIC MOON ROOF SWITCH (MAP LIGHT SUB-ASSEMBLY) |
READ NEXT:
Position Initialization Incomplete (B2343)
DESCRIPTION This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly) has not been initialized. DTC No. Detection Item DTC Detection Condition Trouble Area B2343 P
Motor Control Relay Stuck ON (B2345)
DESCRIPTION This DTC will be stored if the operation of the sliding roof is suspended and a pulse input of 10 Hz or more is detected when the motor relay is off. DTC No. Detection Item DTC Dete
Lost Communication with Front Shade Module (B2346)
DESCRIPTION This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly) stops for 10 seconds or m
SEE MORE:
System Description
SYSTEM DESCRIPTION POWER MIRROR CONTROL SYSTEM (w/ Memory) DESCRIPTION (a) This system has the following functions: electrical remote control mirror function, memory and reactivation function, power retract mirror function, auto power retract mirror function, mirror heater function and automatic gla
Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch
DESCRIPTION The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (front passenger door) v
