Lexus ES: Slip Indicator Light Remains ON
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.
If the skid control ECU (brake booster with master cylinder assembly) stores a DTC, the slip indicator light comes on in the combination meter assembly.
The slip indicator light blinks during ABS, VSC and/or TRAC operation.
When the system is malfunctioning, the slip indicator light comes on to warn the driver.
Click here .gif)
WIRING DIAGRAM
Refer to Brake Control Warning Light Remains ON.
Click here
CAUTION / NOTICE / HINT
NOTICE:
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click here
PROCEDURE
| 1. | CHECK CAN COMMUNICATION SYSTEM |
(a) Check if CAN communication system DTCs are output.
Click here
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
| B | .gif) | INSPECT CAN COMMUNICATION SYSTEM |
|
.gif)
| 2. | CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED |
(a) Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.
OK:
The connector is securely connected.
| NG | | CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY |
|
| 3. | CHECK AUXILIARY BATTERY |
(a) Check the auxiliary battery voltage.
Standard Voltage:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery | Power switch on (IG) | 11 to 14 V |
| Auxiliary battery | Power switch on (READY) | 11 to 15.5 V |
| NG | | CHARGE OR REPLACE AUXILIARY BATTERY |
|
| 4. | READ VALUE USING TECHSTREAM (SLIP INDICATOR LIGHT) |
(a) Select the Data List on the Techstream.
Click here
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Slip Indicator Light | Slip indicator light | ON or OFF | ON: Indicator light on OFF: Indicator light off | - |
| Tester Display |
|---|
| Slip Indicator Light |
(b) Check the Techstream display condition of the slip indicator light.
| Result | Proceed to |
|---|---|
| ON is displayed. | A |
| OFF is displayed. | B |
| A | | REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
| B | | INSPECT METER / GAUGE SYSTEM |
READ NEXT:
System Diagram
SYSTEM DIAGRAM Transmitting ECU (Transmitter) Receiving ECU Signal Communication Method Skid control ECU (Brake booster with master cylinder assembly) Power steering ECU (Rack an
Terminals Of Ecu
TERMINALS OF ECU TERMINALS OF ECU *a Component without harness connected (Skid Control ECU (Brake Booster with Master Cylinder Assembly)) - - Terminal No. (Symbol) Terminal Descripti
Test Mode Procedure
TEST MODE PROCEDURE WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK (a) When the power switch is turned on (IG), check that the ABS warning, brake warning / red (malfunction), brake warning / yellow (
SEE MORE:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Panoramic View Monitor System DTC No. Detection Item DTC Detection Condition Link C1611 ECU Malfunction When any of the following conditions is met:
EEPROM status (Initial read) malfunction
CPU communication malfunction
Video output malfunction
Components
COMPONENTS ILLUSTRATION *1 ENGINE OIL LEVEL SENSOR *2 NO. 2 OIL PAN SUB-ASSEMBLY *3 OIL STRAINER SUB-ASSEMBLY *4 OIL STRAINER GASKET N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
