Lexus ES manuals

Lexus ES: Right Front Wheel Speed Sensor Circuit Intermittent (C05061F)

DESCRIPTION

Refer to DTC C050612

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C05061F

Right Front Wheel Speed Sensor Circuit Intermittent

  • The speed sensor signal is excessively noisy.
  • The calculated change in wheel speed is more than 980 m/s2 for 5*1 or 20*2 seconds or more.
  • The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2 for 5*1 or 20*2 seconds or more.
  • When the vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds for 5*1 or 20*2 seconds or more.
  • Front speed sensor RH
  • Front speed sensor rotor RH (front axle hub sub-assembly RH)
  • *1: The stop light switch assembly is OFF.
  • *2: The stop light switch assembly is ON.
DTC Detection Conditions: C05061F
 

Vehicle Condition

Pattern 1

Pattern 2

Pattern 3

Pattern 4

Diagnosis Condition

The Stop light switch assembly is OFF.

-

Malfunction Status

The speed sensor signal is excessively noisy.

-

-

-

The calculated change in wheel speed is more than 980 m/s2.

-

-

-

The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2.

-

-

-

The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds.

-

-

-

Detection Time

-

5 seconds or more.

5 seconds or more.

5 seconds or more.

Number of Trips

1 trip

1 trip

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C05061F
 

Vehicle Condition

Pattern 5

Pattern 6

Pattern 7

Diagnosis Condition

The stop light switch assembly is ON.

Malfunction Status

The calculated change in wheel speed is more than 980 m/s2.

-

-

The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2.

-

-

The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds.

-

-

Detection Time

20 seconds or more.

20 seconds or more.

20 seconds or more.

Number of Trips

1 trip

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

CAUTION / NOTICE / HINT

NOTICE:

  • After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

    Click here

  • After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

    Click here

  • DTC precaution

    Click here

    Procedure to clear warning lights (When not clearing DTCs)

    Procedure

    1. Repair or replacement.
    2. Turn the engine switch on (IG).
    3. Drive the vehicle at 54 km/h (34 mph) or more for 3 seconds or more to clear the warning lights.

PROCEDURE

1.

CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

(a) Remove the front speed sensor RH.

Click here

(b) Check the front speed sensor RH.

OK:

The front speed sensor RH tip is free of oil and foreign matter.

HINT:

If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor RH, this DTC may be stored.

NG

GO TO STEP 7

OK

2.

CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

(a) Remove the component with the front speed sensor rotor RH.

Click here

(b) Check the front speed sensor rotor RH.

OK:

The front speed sensor rotor RH is free of oil and foreign matter.

HINT:

If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor rotor RH, this DTC may be stored.

OK

REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH

NG

3.

CLEAN FRONT SPEED SENSOR ROTOR RH

(a) Clean the front speed sensor rotor RH.

NOTICE:

Do not use parts cleaner when cleaning the front speed sensor rotor RH.

NEXT

4.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Clear DTCs

(d) Press the DTC clear button.

NEXT

5.

PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

Click here

Chassis > Brake/EPB > Utility

Tester Display

Signal Check

OK:

Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

NG

REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH

OK

6.

RECONFIRM DTC

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

(d) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes

(e) Check if the same DTC is output.

Result

Proceed to

C05061F is not output

A

C05061F is output

B

A

END

B

REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH

7.

CLEAN FRONT SPEED SENSOR RH

(a) Clean the front speed sensor RH.

NOTICE:

When cleaning the front speed sensor RH, make sure to clean the installation hole before installation.

NEXT

8.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Clear DTCs

(d) Press the DTC clear button.

NEXT

9.

PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

Click here

Chassis > Brake/EPB > Utility

Tester Display

Signal Check

OK:

Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

NG

GO TO STEP 2

OK

10.

RECONFIRM DTC

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

(d) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes

(e) Check if the same DTC is output.

Result

Proceed to

C05061F is not output

A

C05061F is output

B

A

END

B

GO TO STEP 2

READ NEXT:

 Right Rear Wheel Speed Sensor Circuit Voltage Out of Range (C05121C)

DESCRIPTION Refer to DTC C051212 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C05121C Right Rear Wheel Speed Sensor Circuit Voltage Out of Range When th

 Right Rear Wheel Speed Sensor Circuit Voltage Out of Range (C05121C)

DESCRIPTION Refer to DTC C051212 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C05121C Right Rear Wheel Speed Sensor Circuit Voltage Out of Range When th

 Right Rear Wheel Speed Sensor Circuit Intermittent (C05121F)

DESCRIPTION Refer to DTC C051212 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C05121F Right Rear Wheel Speed Sensor Circuit Intermittent The speed senso

SEE MORE:

 Components

COMPONENTS ILLUSTRATION *1 ENGINE WIRE *2 NO. 1 VACUUM HOSE CONNECTOR *3 VACUUM PUMP ASSEMBLY *4 NO. 1 VACUUM PUMP O-RING Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable par

 GNSS Antenna Circuit Short to Ground (B15C111,B15C113)

DESCRIPTION These DTCs are stored when a malfunction occurs in the telephone and GPS antenna assembly (for Roof Side) circuit. DTC No. Detection Item DTC Detection Condition Trouble Area B15C111 GNSS Antenna Circuit Short to Ground Current to the GNSS antenna is lower than the malfu

© 2016-2024 Copyright www.lexguide.net