Lexus ES manuals

Lexus ES: Precaution

PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the cable is reconnected.

System Name

See Procedure

Lane Control System (for HV Model)

Parking Support Brake System (for HV Model)

Parking Assist Monitor System (for HV Model)

Panoramic View Monitor System (for HV Model)

Pre-collision System (for HV Model)

Power Trunk Lid System (for HV Model)

Lighting System (for HV Model)

POINTS TO NOTE WHEN SERVICING

(a) Pay attention to the following points when servicing.

(1) Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

HINT:

Each adjusted value for the calibration of the parking assist monitor system will be stored in the rear television camera assembly.

(2) When the lens of the rear television camera assembly is dirty, wash the lens with water and wipe it off with a soft cloth to obtain clear images. For heavy dirt, use neutral detergent to clean the lens.

NOTES FOR REAR TELEVISION CAMERA ASSEMBLY

(a) Notes for the rear television camera assembly

(1) The parking assist monitor system may not function properly if subjected to a severe blow by any hard object.

(2) Do not scrub the camera lens. Scrubbing may scratch the camera lens and affect the image.

(3) The cover part of the camera is made of resin. Prevent organic solvents, waxes, bond removing solvents or glass coating from adhering to the cover. If such material adheres to the cover, clean it off immediately and wash it with water.

(4) Exposing the camera to a sudden temperature change may affect proper functioning of the camera.

(5) A clear image may not appear if the camera is dirty with snow, mud, etc. In that case, wash it with water and wipe off the lens. Use a detergent to remove dirt if necessary.

(6) When washing the vehicle with a high-pressure washer, do not spray water on the rear television camera assembly or surrounding area. High-pressure water can damage the camera.

(b) Images may be unclear even in normal conditions if:

(1) Electrical devices are used in the cabin (noise may occur in the image).

(2) Accessories that generate radio waves have been installed (noise may occur in the image).

(3) The outer mirror switch assembly is operated (noise may occur in the image).

(4) The multi-display is cold (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).

(5) The camera lens is dirty with snow, mud, etc.

(6) A strong beam of light, such as a sunbeam or headlight, hits the camera.

(7) It is too dark around the camera (at night etc.).

(8) The ambient temperature around the camera is either too high or too low.

(9) The vehicle is tilted at a steep angle.

(10) The rear television camera assembly lens is scratched.

(11) The rear television camera assembly lens has drops of water on it or the humidity is high.

(12) When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.

READ NEXT:

 Problem Symptoms Table

PROBLEM SYMPTOMS TABLE NOTICE: The following inspection procedures for the parking assist monitor system are based on the assumption that the audio and visual system*1 or navigation system*2 is nor

 Reverse Signal Circuit

DESCRIPTION The multi-display receives a reverse signal from the BK UP LP relay*1 or clearance warning ECU assembly*2. *1: w/o Parking Support Alert System *2: w/ Parking Support Alert System

 System Description

SYSTEM DESCRIPTION GENERAL (a) This system has a rear television camera assembly mounted on the luggage compartment door to display an image of the area behind the vehicle on the multi-display. The mu

SEE MORE:

 Test Mode Procedure

TEST MODE PROCEDURE NOTICE: After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly. After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) ins

 Parts Location

PARTS LOCATION ILLUSTRATION *1 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) *2 COMBINATION METER ASSEMBLY *3 DLC3 *4 CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) *5 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-B NO. 2 FUSE - DOOR F/L FUSE - DOOR F/R FUSE - DOOR R/L FUSE - DOO

© 2016-2024 Copyright www.lexguide.net