Lexus ES: Operation Check
OPERATION CHECK
CHECK DOOR OPEN LINKED WIPER SUSPEND FUNCTION (w/ Auto Wiper System)
(a) Continuously apply water to the windshield glass in front of the rain sensor.
(b) Turn the power switch on (IG).
(c) Move the windshield wiper switch assembly to the AUTO position and check that the front wipers operate.
(d) Open the driver door or front passenger door and check that the front wipers stop.
CHECK SERVICE POSITION CONTROL
(a) Turn the power switch off.
(b) Within approximately 45 seconds of turning the power switch off, hold the windshield wiper switch assembly in the MIST position for 2 seconds and confirm that the wipers move to the uppermost position.
CHECK AUTO WIPER FUNCTION (w/ Auto Wiper System)
(a) Continuously apply water to the windshield glass in front of the rain sensor.
(b) Turn the power switch on (IG).
(c) Move the windshield wiper switch assembly to the AUTO position.
(d) Check that the front wipers operate.
CHECK INTERMITTENT CONTROL FUNCTION
HINT:
When the AUTO wiper function is disabled through a customize setting, the intermittent control function can be operated.*1
Click here .gif)
(a) Turn the power switch on (IG).
(b) Move the windshield wiper switch assembly to the AUTO*1 or INT*2 position.
(c) Check that the intermittent operation interval can be adjusted from approximately 4 to 12.5 seconds by operating the auto sensitivity adjustment switch.
- *1: w/ Auto Wiper System
- *2: w/o Auto Wiper System
CHECK VEHICLE SPEED SENSING TYPE ADJUSTABLE INTERMITTENT WIPER CONTROL
HINT:
When the AUTO wiper function is disabled through a customize setting, the intermittent control function can be operated.*1
Click here
(a) Turn the power switch on (IG).
(b) Move the windshield wiper switch assembly to the AUTO*1 or INT*2 position.
(c) Check that the intermittent operation interval changes from approximately 1.5 to 11 seconds according to the vehicle speed and the position of the auto sensitivity adjustment switch of the windshield wiper switch assembly.
- *1: w/ Auto Wiper System
- *2: w/o Auto Wiper System
WASHER OPERATION INSPECTION
(a) Turn the power switch on (IG).
(b) Washer operation inspection:
Operate the washer switch for approximately 0.5 seconds or more and confirm that the front wipers operate in the LO setting when the washer fluid is sprayed and that the front wipers cycle 3 times after releasing the washer switch.
(c) Drip prevention wiper function:
Operate the washers and check that approximately 3 seconds after washer cooperation operates, the wipers operate 1 cycle.
NOTICE:
Perform this inspection with the vehicle stopped.
LEVEL WARNING OPERATION INSPECTION
(a) When the volume of washer fluid decreases to below a certain level (when the level warning switch is turned on), the multi-information display warns the driver by displaying a message.
READ NEXT:
Customize Parameters
CUSTOMIZE PARAMETERS NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customiz
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: Before replacing the main body ECU (multiplex network body ECU), refer to Registration. Click here HINT:
Use the table below to help determine the cause of problem
Utility
UTILITY OPERATION HISTORY HINT: History of Reason for Operation: The windshield wiper motor assembly stores Operation History which can be read using the Techstream, when a malfunction of the wiper an
SEE MORE:
High Pressure Fuel Pump Circuit Open (P123513)
DESCRIPTION The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor, fuel pump assembly (for high pressure side) and direct fuel injector assemblies. The spill control valve adjusts the return volume of the high-pressure
Test Mode Procedure
TEST MODE PROCEDURE TEST MODE (SIGNAL CHECK MODE) PROCEDURE HINT:
When entering test mode (signal check mode), the tire pressure warning ECU and receiver sets all the test mode (signal check mode) DTCs first.
After the tire pressure warning ECU and receiver completes the signal check for each ins
