Lexus ES manuals

Lexus ES: Motor Drive Permission Malfunction (C1451)

DESCRIPTION

If air bleeding has not been performed, the skid control ECU (brake booster with master cylinder assembly) stores DTC C1451 to prevent the entry of air due to pump motor operation.

DTC C1451 is stored when Motor Invalid is selected, the system will not return to normal until the air bleeding procedure is performed.

DTC No.

Detection Item

INF Code

DTC Detection Condition

Trouble Area

MIL

Note

C1451

Motor Drive Permission Malfunction

1152

Either of the following is detected:

  • Using the Techstream, "Motor Invalid" of the "ECB Utility" has been performed.
  • The brake booster with master cylinder assembly has been replaced.

Air bleeding not performed

Only DTC C1451 (INF code 1152) is stored: Does not come on

SAE Code C1451 is stored: Comes on

  • INF Code 1152: SAE Code C1451
  • Electronically controlled brake system DTC

HINT:

  • DTC C1451 (INF code 1152) is cleared when the conditions return to normal.
  • ECB: Electronically Controlled Brake System

MONITOR DESCRIPTION

SAE Code C1451:
  • After replacing the skid control ECU (brake booster with master cylinder assembly) or brake booster pump assembly, if air bleeding is not performed and the vehicle is driven at a certain speed or more, the skid control ECU (brake booster with master cylinder assembly) judges that air bleeding has not been completed and illuminates the MIL and stores this DTC.

    Furthermore, this DTC is not cleared until air bleeding has been completed.

C1451 (INF Code 1152):
  • After replacing the skid control ECU (brake booster with master cylinder assembly) or brake booster pump assembly, if air bleeding is not performed, the skid control ECU (brake booster with master cylinder assembly) judges that air bleeding has not been completed and illuminates the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights, blinks* the brake hold operated indicator light and stores this DTC.

    Furthermore, this DTC is not cleared until air bleeding has been completed.

    HINT:

    • *: The brake hold switch (No. 3 combination switch assembly) is turned on under the following vehicle conditions.
      • Vehicle Conditions:
        1. The driver side door is closed.
        2. The driver side seat belt is fastened.
    • As the detection conditions slightly differ from SAE code C1451, the detection conditions for DTC C1451 (INF code 1152) is also provided.

MONITOR STRATEGY

HINT:

SAE code only.

C1451

Related DTCs

C1451: High pressure hydraulic tube air bleeding not complete

Required Sensors/Components(Main)

High pressure hydraulic tube

Required Sensors/Components(Related)

Speed sensor

Frequency of Operation

Continuous

Duration

-

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

HINT:

SAE code only.

C1451

Monitor runs whenever the following DTCs are not stored

None

Vehicle speed

40 km/h (25 mph) or more

TYPICAL MALFUNCTION THRESHOLDS

HINT:

SAE code only.

C1451

High pressure hydraulic tube air bleeding

Not complete

COMPONENT OPERATING RANGE

HINT:

SAE code only.

C1451

High pressure hydraulic tube air bleeding

Complete

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off.
  6. Turn the power switch on (READY).
  7. Turn the Techstream on.
  8. Drive the vehicle at a speed of 40 km/h (25 mph) or more for 1 second.
  9. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
  10. Read the DTCs.

    HINT:

    • If a DTC is output, the system is malfunctioning.
    • If a DTC is not output, perform the following procedure.
  11. If the DTCs are not output, perform a universal trip and check for permanent DTCs.

    Click here

    HINT:

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTCs are output, the system is normal.

PROCEDURE

1.

PERFORM AIR BLEEDING

(a) Bleed the air from the brake system.

Click here

HINT:

If air bleeding has been performed, this DTC will be cleared.

NEXT

2.

RECONFIRM DTC

(a) Check if the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

DTC C1451 is output.

A

DTC C1451 is not output.

B

A

PERFORM AIR BLEEDING AGAIN

B

END

READ NEXT:

 Calibration

CALIBRATION DESCRIPTION (a) After replacing any VSC related components or performing wheel alignment adjustment, clear and read the sensor calibration data. Refer to the table below and then perform t

 Check For Intermittent Problems

CHECK FOR INTERMITTENT PROBLEMS CHECK FOR INTERMITTENT PROBLEMS HINT: A momentary interruption (open circuit) in the connectors and/or wire harnesses between the sensors and ECUs can be detected using

 Data List / Active Test

DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa

SEE MORE:

 Insufficient Coolant Temperature for Closed Loop Fuel Control (P012500)

DESCRIPTION Refer to DTC P011511. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P012500 Insufficient Coolant Temperature for Closed Loop Fuel Control The engine coolant temperature does not reach the closed loop enabling temperature f

 Reaction Force Pressure Sensor Power Supply Voltage Malfunction (C14B0,...,C14D4)

DESCRIPTION DTC No. Detection Item INF Code DTC Detection Condition Trouble Area MIL Note C14B0 Reaction Force Pressure Sensor Power Supply Voltage Malfunction 201 The supplied voltage to the sensor is less than 6.3 V or 7.7 V or more for 0.05 seconds or more. Skid control

© 2016-2024 Copyright www.lexguide.net