Lexus ES: Left Rear Wheel Speed Sensor Signal Stuck Low (C050C23)
DESCRIPTION
Refer to DTC C050C12
Click here .gif)
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C050C23 | Left Rear Wheel Speed Sensor Signal Stuck Low |
| Rear speed sensor LH (rear axle hub and bearing assembly LH) |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | The vehicle is driven from 0 km/h to 12 km/h (0 mph to 7 mph). | ○ | - | - |
| The vehicle speed reaches 18 km/h (11 mph). | - | ○ | - | |
| The vehicle speed and wheel speed are both 43.2 km/h (26.8 mph) or more. | - | - | ○ | |
| Malfunction Status | The wheel speed is 1.8 km/h (1.1 mph) or less. | ○ | - | - |
| The wheel speed has not exceeded 1.8 km/h (1.1 mph). | - | ○ | - | |
| The pulse signal is not detected. | - | - | ○ | |
| Detection Time | 0.6 seconds or more. | - | 0.08 seconds or more. | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
-
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Click here
-
DTC precaution
Click here
Procedure to clear warning lights (When not clearing DTCs) Procedure
- Repair or replacement.
- Turn the engine switch on (IG).
- Drive the vehicle at 2 km/h (1 mph) or more to clear the warning lights.
PROCEDURE
| 1. | CHECK FREEZE FRAME DATA (WHEEL SPEED) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
(d) Select a DTC to display the Freeze Frame Data.
(e) Read the freeze frame data of DTC C050C23.
Chassis > Brake/EPB| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
| Result | Proceed to |
|---|---|
| The value of RL Wheel Speed is 2 km/h (1 mph) or less when all other values are 12 km/h (7 mph) or more. | A |
| The value of RL Wheel Speed is 2 km/h (1 mph) or less when all other values are 43 km/h (27 mph) or more. | B |
| B |  | REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH |
|
| 2. | READ VALUE USING TECHSTREAM (RL WHEEL SPEED) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Enter the following menus: Chassis / Brake/EPB / Data List.
Chassis > Brake/EPB > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RL Wheel Speed |
(d) Start the engine and perform a road test.
(e) Check that the value of RL Wheel Speed changes in accordance with vehicle speed when accelerating from 0 km/h to 20 km/h (0 mph to 12 mph).
OK:
The value of RL Wheel Speed changes in accordance with vehicle speed.
HINT:
If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation such as brake drag, wheelspin or wheel lockup.
| OK | | USE SIMULATION METHOD TO CHECK |
| NG | | REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH |
READ NEXT:
Left Rear Wheel Speed Sensor Signal Stuck Low (C050C23)
DESCRIPTION Refer to DTC C050C12 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C050C23 Left Rear Wheel Speed Sensor Signal Stuck Low
When the vehicle is
Left Rear Wheel Speed Sensor Signal Stuck High (C050C24)
DESCRIPTION Refer to DTC C050C12 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C050C24 Left Rear Wheel Speed Sensor Signal Stuck High The speed sensor signa
Left Rear Wheel Speed Sensor Signal Stuck High (C050C24)
DESCRIPTION Refer to DTC C050C12 Click here DTC No. Detection Item DTC Detection Condition Trouble Area C050C24 Left Rear Wheel Speed Sensor Signal Stuck High The speed sensor signa
SEE MORE:
Transmitter ID1 Operation Stop (C2111-C2114)
DESCRIPTION The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tir
System Description
SYSTEM DESCRIPTION LIN COMMUNICATION SYSTEM DESCRIPTION The LIN communication system is used for communication between the components in the tables below. If communication cannot be performed through LIN communication such as when there is an open or short in a communication line, the master control
