Lexus ES: Installation
INSTALLATION
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. INSTALL KICK DOOR CONTROL SENSOR (except 2GR-FKS)
(a) Engage the guide as shown in the illustration.
.png) | Install in this Direction (1) |
.png) | Install in this Direction (2) |
NOTICE:
- Do not subject the kick door control sensor to a strong impact or drop it.
- Do not reuse a kick door control sensor which has been subjected to a strong impact or dropped.
- Be careful not to pull the wire harness.
- Be careful not to twist the wire harness.
(b) Install the screw.
(c) Engage the 16 claws with each marking on the kick door control sensor facing up to install the kick door control sensor as shown in the illustration.
.png) | Marking (White) | - | - |
NOTICE:
Fully insert the kick door control sensor into the kick door control bracket.
HINT:
Engage each claw in the order shown in the illustration.
3. INSTALL KICK DOOR CONTROL SENSOR (for 2GR-FKS)
(a) Engage the guide to install the kick door control sensor as shown in the illustration.
| | Install in this Direction (1) |
| | Install in this Direction (2) |
NOTICE:
- Do not subject the kick door control sensor to a strong impact or drop it.
- Do not reuse a kick door control sensor which has been subjected to a strong impact or dropped.
- Be careful not to pull the wire harness.
- Be careful not to twist the wire harness.
(b) Install the screw.
(c) Engage the 16 claws with each marking on the kick door control sensor facing up to install the kick door control sensor as shown in the illustration.
| | Marking (White) | - | - |
NOTICE:
Fully insert the kick door control sensor into the kick door control bracket.
HINT:
Engage each claw in the order shown in the illustration.
4. INSTALL KICK DOOR CONTROL SENSOR WITH BRACKET (except 2GR-FKS)
(a) Engage the claw as shown in the illustration.
| | Install in this Direction | - | - |
(b) Install the 3 screws.
(c) Install the kick door control sensor with bracket with the 2 clips.
(d) Engage the clamp.
(e) Connect the connector.
NOTICE:
Do not touch the terminals of the kick door control sensor connector.
5. INSTALL KICK DOOR CONTROL SENSOR WITH BRACKET (for 2GR-FKS)
(a) Engage the claw as shown in the illustration.
| | Install in this Direction | - | - |
(b) Install the 3 clips.
(c) Install the kick door control sensor with bracket with the 2 screws.
(d) Engage the clamp.
(e) Connect the connector.
NOTICE:
Do not touch the terminals of the kick door control sensor connector.
6. INSTALL REAR BUMPER ASSEMBLY (for Single Type)
Click here .gif)
7. INSTALL REAR BUMPER ASSEMBLY (for Dual Type)
Click here
8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for 2GR-FKS:
Click here
for A25A-FXS:
Click here
9. INITIALIZE KICK DOOR CONTROL SENSOR
for Gasoline Model:
Click here
for HV Model:
Click here
10. INSPECT KICK DOOR CONTROL SENSOR
for Gasoline Model:
Click here
for HV Model:
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION *A w/ Power Trunk Lid System - - *1 LUGGAGE COMPARTMENT DOOR ASSIST GRIP *2 LUGGAGE COMPARTMENT DOOR COVER *3 LUGGAGE LOCK CONTROL CABLE PLATE *4
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during
SEE MORE:
Telescopic Position Sensor or Telescopic Motor Circuit Component Internal Failure (B261196)
DESCRIPTION The telescopic motor (steering column assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column assembly forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor (steering column asse
Reverse Shift-linked Function of Power Mirrors does not Operate
DESCRIPTION The ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Based on the signal, eac
