Lexus ES manuals

Lexus ES: High Voltage Fuse Accumulated Load History (P0A9563)

DESCRIPTION

The battery ECU assembly estimates the thermal load of the high voltage fuse. If the accumulated thermal load exceeds the threshold, the battery ECU assembly will store this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P0A9563

High Voltage Fuse Accumulated Load History

Accumulated thermal load of the high voltage fuse estimated by the battery ECU assembly exceeds the threshold.

(1 trip detection logic)

Hybrid battery terminal block

Does not come on

Master Warning Light:

Does not come on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 2 minutes or more.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. With power switch on (IG) and wait for 5 seconds or more.
  7. Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.

CAUTION / NOTICE / HINT

HINT:

If the hybrid battery terminal block has been replaced, make sure to perform "High Voltage Fuse Accumulated Load History Reset" and then clear the DTCs.

PROCEDURE

1.

REPLACE HYBRID BATTERY TERMINAL BLOCK

Click here

NEXT

2.

PERFORM UTILITY (HIGH VOLTAGE FUSE ACCUMULATED LOAD HISTORY RESET)

Click here

NEXT

3.

CLEAR DTC (HV BATTERY)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Enter the following menus: Powertrain / HV Battery / Clear DTCs.

(d) Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs

(e) Turn the power switch off.

NEXT

END

READ NEXT:

 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground (P0A9B11,...,P0C3315)

DESCRIPTION The battery temperature sensors are provided at 6 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance w

 Hybrid/EV Battery Temperature Sensor "A" Voltage Out of Range (P0A9B1C,P0AC51C,P0ACA1C,P0AE81C,P0BC21C,P0C331C)

DESCRIPTION Refer to the description for DTC P0A9B11. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0A9B1C Hybrid/EV Battery Tempera

 Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range (P0A9B2A,...,P306A62)

DESCRIPTION Refer to the description for DTC P0A9B11. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0A9B2A Hybrid/EV Battery Tempera

SEE MORE:

 Headlight LH Circuit (B2439,B243A)

DESCRIPTION The headlight ECU sub-assembly LH and headlight ECU sub-assembly RH internally boost the power supply voltage to ensure a constant supplied current for the lo/hi beam LED of their respective headlight. By monitoring the LED power supply voltage, abnormal current and malfunctions can be d

 Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY (a) Disengage the 3 claws and 2 pins. (b) Move the roof wind deflector panel sub-assembly in the direction indicated by the arrow (1) shown in the illustration. Remove in this Direction (1) Remove in this Direction

© 2016-2024 Copyright www.lexguide.net