Lexus ES: Deceleration Sensor (C1245)
DESCRIPTION
The parking brake ECU (brake actuator assembly) receives vehicle tilt angle information from the deceleration sensor (airbag ECU assembly) via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C1245 | Deceleration Sensor | One of following conditions is met:
| Deceleration sensor (Airbag ECU assembly) | DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Power switch on (IG) | ○ | ○ | ○ |
| Malfunction Status | An error signal is sent from the deceleration sensor (airbag ECU assembly) | ○ | - | - |
| While the deceleration sensor (airbag ECU assembly) signal is judged to be stuck, starting off and stopping the vehicle occurs 16 times | - | ○ | - | |
| Comparison error between deceleration sensor (airbag ECU assembly) 1 and deceleration sensor (airbag ECU assembly) 2 output values occurs | - | - | ○ | |
| Detection Time | Approximately 0.3 seconds | - | 60 seconds or more | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
When replacing the deceleration sensor (airbag ECU assembly), perform initialization and calibration of the linear solenoid valve.
Click here .gif)
PROCEDURE
| 1. | CHECK DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM) |
(a) Check for DTCs.
Chassis > ABS/VSC/TRC > Trouble Codes| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
| B | .gif) | GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM |
|
.gif)
| 2. | CHECK DTC (ELECTRIC PARKING BRAKE SYSTEM) |
(a) Clear the DTCs.
Chassis > Electric Parking Brake > Clear DTCs(b) Turn the power switch off.
(c) Check for DTCs.
Chassis > Electric Parking Brake > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
| A | | REPLACE AIRBAG ECU ASSEMBLY |
| B | | USE SIMULATION METHOD TO CHECK |
READ NEXT:
Data List / Active Test
DATA LIST / ACTIVE TEST READ DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any part
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Electric Parking Brake System DTC No. Detection Item Memory Note Link C1245 Deceleration Sensor DTC stored An electric parking brake system malfuncti
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC AND FREEZE FRAME DATA (USING TECHSTREAM) (a) Turn the power switch off. (b) Connect the Techstream to the DLC3. (c) Turn the power switch on (IG). (d) Turn the Techstream o
SEE MORE:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Dynamic Torque Control AWD System DTC No. Detection Item Link C120C Linear Solenoid Power Supply System Malfunction C1241 Low or High Power Supply Voltage C1280 Engine Circuit Malfunction C1296 ABS Malfunction C1297
Charging Failure
PROCEDURE 1. CHECK GENERATOR PULLEY WITH CLUTCH (ON-VEHICLE INSPECTION) (a) Start the engine and visually check that the generator rotor assembly (fan) in the generator assembly is operating. OK: The generator rotor assembly (fan) is operating. NG REPLACE GENERATOR PULLEY WITH CLUTC
