Lexus ES: Cellular Phone Inspection
PROCEDURE
| 1. | CHECK USAGE CONDITION |
(a) Check that the vehicle and cellular phone meet the following conditions:
NOTICE:
If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.
-
The cellular phone is "Bluetooth" compatible.
Click here
.gif)
- The cellular phone is registered as a hands-free device.
- "Bluetooth" setting of the cellular phone is on.
- Operating system and software of the cellular phone are the latest versions.
- There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.
- The "Wi-Fi" setting of the cellular phone is off.
- The "Wi-Fi" tethering setting of the cellular phone is off.
(b) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | .gif) | END |
|
.gif)
| 2. | RESTART CELLULAR PHONE |
(a) Restart the cellular phone.
(b) Turn the power switch off.
(c) Turn the power switch on (ACC).
(d) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END |
|
| 3. | CHECK OPERATION |
(a) Check if the in-vehicle device can be recognized by the cellular phone.
| Result | Proceed to |
|---|---|
| In-vehicle device can be recognized. | A |
| In-vehicle device cannot be recognized. | B |
| B | | GO TO STEP 5 |
|
| 4. | REGISTER AGAIN |
(a) Clear all "Bluetooth" devices registered to the cellular phone and the radio receiver assembly.
(b) Register the cellular phone again.
(c) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END |
|
| 5. | CHECK USING ANOTHER VEHICLE |
(a) Check if the customer's cellular phone functions normally using another "Bluetooth" compatible vehicle.
HINT:
- Make sure to obtain the customer's permission to perform this procedure.
- After the inspection, clear the registered information and usage history acquired during the inspection.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
| 6. | CHECK USING ANOTHER CELLULAR PHONE |
(a) Check if the system functions normally using another "Bluetooth" compatible cellular phone.
HINT:
- Make sure to obtain the customer's permission to perform this procedure.
- After the inspection, clear the registered information and usage history acquired during the inspection.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED) |
| B | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
READ NEXT:
Cellular Phone Registration Failure
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZING WITH REMOTE TOUCH (a) Customizing with the touch function cancellation function. (w/ Touch Function Cancellation Function) NOTICE: Confirm the touchpad surface is free
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa
SEE MORE:
Cold Start Ignition Timing Performance (P050B00)
MONITOR DESCRIPTION This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC is stored after the engine idles for 13 seconds (2 trip detection logic). The DTC is designed to monitor the ignition timing at cold start. When the engine is
Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery (P212012,P212014,P21201C,P21201F,P212099,P212512,P212514,P21251F,P21382B)
DESCRIPTION HINT:
This Electronic Throttle Control System (ETCS) does not use a throttle cable.
These DTCs relate to the accelerator pedal position sensor.
The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2
