Lexus ES manuals

Lexus ES: ECU Malfunction (C1611)

DESCRIPTION

This DTC is stored if the rear television camera assembly judges that there is an internal malfunction as a result of its self check.

HINT:

The rear television camera assembly stores different types of information during initialization. If the rear television camera assembly cannot read the stored information when it is activated, the rear television camera assembly judges that there is an internal malfunction and stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1611

ECU Malfunction

When any of the following conditions is met:

  • EEPROM status (Initial read) malfunction
  • CPU communication malfunction
  • Video output malfunction

Rear television camera assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

PROCEDURE

1.

READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / Rear Camera / Data List.

(e) Read the Data List according to the display on the Techstream,

Chassis > Rear Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Video Output Status

Output condition of video signal

OK or NG

OK: Output condition of video signal is normal

NG: Output condition of video signal is abnormal

-

EEPROM Status (Initial read)

Rear television camera assembly information

OK or NG

OK: Rear television camera assembly normal

NG: Rear television camera assembly abnormal

-

CPU Communication Status

Rear television camera assembly information

OK or NG

OK: Rear television camera assembly normal

NG: Rear television camera assembly abnormal

-

Chassis > Rear Camera > Data List

Tester Display

Video Output Status

EEPROM Status (Initial read)

CPU Communication Status

Result

Proceed to

OK is displayed for all items

A

NG is displayed for EEPROM status (Initial read)

NG is displayed for items other than EEPROM status (Initial read)

B

B

REPLACE REAR TELEVISION CAMERA ASSEMBLY

A

2.

PERFORM CALIBRATION

(a) Perform the following procedure depending on the memory conditions to register the vehicle information into the rear television camera assembly.

(1) Rear television camera assembly optical axis adjustment (back camera position setting).

Click here

(2) Steering angle setting.

Click here

NEXT

3.

CHECK DTC OUTPUT

(a) Clear the DTCs.

Chassis > Rear Camera > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Chassis > Rear Camera > Trouble Codes

HINT:

  • If DTC C1611 is output, perform the procedure to allow the rear television camera assembly to store the vehicle information again.
  • If DTC C1611 is still output after performing the procedure to make the rear television camera assembly store the vehicle information 3 times, replace the rear television camera assembly.

Result

Proceed to

DTC C1611 is output

A

DTC C1611 is not output

B

A

REPLACE REAR TELEVISION CAMERA ASSEMBLY

B

END

READ NEXT:

 Back Camera Power Supply Failure (C1621)

DESCRIPTION This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and multi-displa

 Back Camera Disconnected (C1622)

DESCRIPTION This DTC is stored if the radio receiver assembly judges that the signals or signal lines between the rear television camera assembly and the multi-display assembly are not normal as a res

 Open or Short in Steering Angle Sensor +B (C1625)

DESCRIPTION This DTC is stored if the rear television camera assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem. DTC No. Detection Ite

SEE MORE:

 How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the lighting system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. CUSTOMER PROBLEM ANALYSIS HINT: In troubleshooting, confirm that the problem symptoms h

 Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Panoramic View Monitor System DTC No. Detection Item DTC Detection Condition Link C1611 ECU Malfunction When any of the following conditions is met: EEPROM status (Initial read) malfunction CPU communication malfunction Video output malfunction

© 2016-2024 Copyright www.lexguide.net