Lexus ES manuals

Lexus ES: Dtc Check / Clear

DTC CHECK / CLEAR

DTC CHECK

(a) Turn the engine switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG).

(d) Turn the Techstream on.

(e) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Trouble Codes

(f) Check the details of the DTCs.

NOTICE:

  • Make sure to clear the DTCs after repair.
  • The electronically controlled brake system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the electronically controlled brake system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

    System

    Proceed to

    Electric Parking Brake System (for Gasoline Model)

Display Item

Description

Test Failed

Shows the malfunction judgment results during the current trip.

Confirmed

Shows the DTCs confirmed up to now (The number of current trips differs for each DTC.)

  • Freeze frame data is stored for each of the latest result DTCs and confirmed DTCs.
  • Refer to the diagnostic trouble code chart and perform the necessary troubleshooting procedures.

    Click here

(g) Check the freeze frame data.

(1) If a DTC is stored, check the corresponding freeze frame data to gain an understanding of the vehicle condition at the time.

Click here

CHECK TIME STAMP

HINT:

By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.

(a) Turn the engine switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG).

(d) Turn the Techstream on.

(e) Enter the following menus: Health Check.

(f) Perform the following steps when the data setting screen is displayed.

(g) Select the systems for which to perform Health Check and check for time stamp data.

Selectable items:
  • Powertrain
  • Chassis
  • Body
  • Store All Data

(h) Select "Yes" when "Would you like to include Time Stamp Data?" is displayed.

HINT:

If "Yes" is not selected, time stamp data will not be stored.

(i) After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.

(j) Select the desired system from the drop-down list on the bottom of the Time Stamp screen.

(k) Check the order and time which DTCs were stored for the selected system.

DTC CLEAR

(a) Turn the engine switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG).

(d) Turn the Techstream on.

(e) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

Chassis > Brake/EPB > Clear DTCs

(f) Press the DTC clear button.

NOTICE:

When DTCs are cleared, all data related to the DTCs is also cleared.

HINT:

If the malfunction continues, the DTCs will be stored again when the detection conditions are met.

READ NEXT:

 Excessive Brake Pedal Travel (No Fluid Leaks and No Air in System)

CAUTION / NOTICE / HINT NOTICE: After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization. Click here

 Fail-safe Chart

FAIL-SAFE CHART FAIL-SAFE CHART (a) When the skid control ECU (brake actuator assembly) detects a solenoid valve malfunction or abnormal signal from a sensor, the brake actuator assembly cuts power an

 FL Speed Sensor Wrong Installation (X0451)

DESCRIPTION Code Tester Display Measurement Item Trouble Area X0451 FL Speed Sensor Wrong Installation History of front speed sensor LH being installed incorrectly Front speed senso

SEE MORE:

 Generator Phase U-V-W Current Sensor Signal Compare Failure (P0DFA62,P1C691F)

DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that the current sensor value is abnormal. The cause of this malfunction may be one of the following: Internal inverter malfunction Current sensor malfunction Inverter with converter assembly internal circuit malfunction DESCRIPTION

 Replacement

REPLACEMENT CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub bolt removal/installation are shown below. Necessary Procedures After Parts Removed/

© 2016-2024 Copyright www.lexguide.net