Lexus ES manuals

Lexus ES: D-Seat ECU Vehicle Information Reading/Writing Process Malfunction (B15F8)

Lexus ES (XZ10) Service Manual / Audio & Visual & Telematics / Audio / Video / Audio And Visual System (for Hv Model) / D-Seat ECU Vehicle Information Reading/Writing Process Malfunction (B15F8)

DESCRIPTION

This DTC is stored when items controlled by the main body ECU (multiplex network body ECU) cannot be customized via the audio and visual system vehicle customization screen.

HINT:

The main body ECU (multiplex network body ECU) controls the front power seat control system (w/ Memory) related items that are customizable via the multi-display assembly screen.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B15F8

D-Seat ECU Vehicle Information Reading/Writing Process Malfunction

Main body ECU (multiplex network body ECU) vehicle setting processing malfunction

  • CAN communication system
  • Front power seat control system (w/ Memory)
  • Main body ECU (multiplex network body ECU)
  • Radio receiver assembly

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

    Click here

  • When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio receiver assembly may not operate normally.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

1.

CHECK CAN COMMUNICATION SYSTEM

(a) Use the Techstream to check if the CAN communication system is functioning normally.

Click here

OK:

CAN communication DTCs are not output.

NG

GO TO CAN COMMUNICATION SYSTEM

OK

2.

CHECK FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

(a) Check if the front power seat control system (w/ Memory) is malfunctioning.

Click here

HINT:

Customization may not be possible depending on the malfunction in the front power seat control system (w/ Memory).

OK:

No malfunctions are present in the front power seat control system (w/ Memory).

NG

GO TO FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

OK

3.

CHECK CUSTOMIZE ITEMS

(a) Display the "Vehicle Customization" screen.

(b) Make a note of the customizable items for each main body ECU (multiplex network body ECU).

HINT:

The items shown as customizable via the audio and visual system vehicle customization screen can also be changed using the Techstream. In the following step, the Techstream will be used.

(1) To match-up the items on the multi-display assembly with the items on the Techstream, check the customize parameters list for the front power seat control system (w/ Memory) related items that can be customized via the multi-display assembly screen.

Click here

(c) Using the Techstream, check that it is possible to change the settings of the customize parameters that are available for customization via the multi-display assembly screen.

OK:

The items available for customization via the multi-display assembly screen can be customized successfully using the Techstream.

OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

READ NEXT:

 XM Tuner Antenna Disconnected (B15FE,B15FF)

DESCRIPTION These DTCs are stored when a malfunction occurs in the telephone antenna assembly which is connected to the radio receiver assembly. DTC No. Detection Item DTC Detection Condition

 Touch Pad Vibration Driver Malfunction (B155A)

DESCRIPTION This DTC is stored if the remote touch (remote operation controller assembly) detects a malfunction in itself, such as internal hardware failure or remote touch screen vibration driver mal

 Touch Pad Memory Module Malfunction (B155B)

DESCRIPTION This DTC is stored if the remote touch (remote operation controller assembly) detects a malfunction in itself, such as internal hardware failure or remote touch screen memory module malfun

SEE MORE:

 Replacement

REPLACEMENT PROCEDURE 1. REPLACE INTAKE VALVE GUIDE BUSH (a) Heat the cylinder head sub-assembly to between 80 and 100°C (176 and 212°F). (b) Place the cylinder head sub-assembly on wooden blocks. CAUTION: Be sure to wear protective gloves. (c) Using SST and a hammer, tap out the intake valve g

 Display Malfunction (B15A6,B15B0)

DESCRIPTION These DTCs are stored when a malfunction occurs in the multi-display assembly. DTC No. Detection Item DTC Detection Condition Trouble Area B15A6 Display Malfunction When any of the following conditions is met: RAM error Drawing controller malfunction Internal hard

© 2016-2024 Copyright www.lexguide.net