Lexus ES: Cellular Phone Inspection
PROCEDURE
| 1. | CHECK USAGE CONDITION |
(a) Check that the vehicle and cellular phone meet the following conditions:
NOTICE:
If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.
-
The cellular phone is "Bluetooth" compatible.
Click here
.gif)
- The cellular phone is registered as a hands-free device.
- "Bluetooth" setting of the cellular phone is on.
- Operating system and software of the cellular phone are the latest versions.
- There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.
- The "Wi-Fi" setting of the cellular phone is off.
- The "Wi-Fi" tethering setting of the cellular phone is off.
(b) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | .gif) | END |
|
.gif)
| 2. | RESTART CELLULAR PHONE |
(a) Restart the cellular phone.
(b) Turn the engine switch off.
(c) Turn the engine switch on (ACC).
(d) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END |
|
| 3. | CHECK OPERATION |
(a) Check if the in-vehicle device can be recognized by the cellular phone.
| Result | Proceed to |
|---|---|
| In-vehicle device can be recognized. | A |
| In-vehicle device cannot be recognized. | B |
| B | | GO TO STEP 5 |
|
| 4. | REGISTER AGAIN |
(a) Clear all "Bluetooth" devices registered to the cellular phone and the radio receiver assembly.
(b) Register the cellular phone again.
(c) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END |
|
| 5. | CHECK USING ANOTHER VEHICLE |
(a) Check if the customer's cellular phone functions normally using another "Bluetooth" compatible vehicle.
HINT:
- Make sure to obtain the customer's permission to perform this procedure.
- After the inspection, clear the registered information and usage history acquired during the inspection.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
| 6. | CHECK USING ANOTHER CELLULAR PHONE |
(a) Check if the system functions normally using another "Bluetooth" compatible cellular phone.
HINT:
- Make sure to obtain the customer's permission to perform this procedure.
- After the inspection, clear the registered information and usage history acquired during the inspection.
| Result | Proceed to |
|---|---|
| The cellular phone is connected correctly. | A |
| The cellular phone is not connected correctly. | B |
| A | | END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED) |
| B | | PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
READ NEXT:
Cellular Phone Registration Failure
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
Cursor or Map Rotates when Vehicle Stopped
PROCEDURE 1. CHECK CONDITION (a) Check with the customer if the vehicle has been turned by a turntable. OK: Vehicle has not been turned by a turntable. HINT: If the vehicle is turned on a
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZING WITH REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) (a) Customizing with the touch function cancellation function. (w/ Touch Function Cancellation Function) NOTIC
SEE MORE:
Transmission Range Sensor "A" Circuit Open (P070513,P070562)
DESCRIPTION The park/neutral position switch assembly detects the shift position and sends signals to the ECM. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P070513 Transmission Range Sensor "A" Circuit Open All switches are off simultaneously for
Drive Belt
PrecautionPRECAUTION NOTICE:
Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.
Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
If oi
