Lexus ES: Camera ECU Malfunction (C1610)
DESCRIPTION
This DTC is stored when a malfunction occurs in the parking assist monitor system*1 or panoramic view monitor system*2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1610 | Camera ECU Malfunction | Malfunction occurs in the parking assist monitor system*1 Malfunction occurs in the panoramic view monitor system*2 |
|
-
*1: w/ Parking Assist Monitor System
*2: w/ Panoramic View Monitor System
CAUTION / NOTICE / HINT
NOTICE:
-
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
.gif)
-
When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio receiver assembly may not operate normally.
PROCEDURE
| 1. | CHECK MODEL |
(a) Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Parking Assist Monitor System | A |
| w/ Panoramic View Monitor System | B |
| B | .gif) | GO TO STEP 4 |
|
.gif)
| 2. | CHECK DTC (PARKING ASSIST MONITOR SYSTEM) |
(a) Clear the DTCs.
Chassis > Rear Camera > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Chassis > Rear Camera > Trouble CodesOK:
No DTCs are output.
| NG | | GO TO PARKING ASSIST MONITOR SYSTEM |
|
| 3. | CHECK DTC (NAVIGATION SYSTEM) |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | | END |
| NG | | REPLACE RADIO RECEIVER ASSEMBLY |
| 4. | CHECK DTC (PANORAMIC VIEW MONITOR SYSTEM) |
(a) Clear the DTCs.
Chassis > Rear Camera > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Chassis > Rear Camera > Trouble CodesOK:
No DTCs are output.
| NG | | GO TO PANORAMIC VIEW MONITOR SYSTEM |
|
| 5. | CHECK DTC (NAVIGATION SYSTEM) |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | | END |
| NG | | REPLACE RADIO RECEIVER ASSEMBLY |
READ NEXT:
CD/DVD Sound Skips
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
Cellular Phone Inspection
PROCEDURE 1. CHECK USAGE CONDITION (a) Check that the vehicle and cellular phone meet the following conditions: NOTICE: If changing cellular phone settings, updating software, etc. is necessa
Cellular Phone Registration Failure
CAUTION / NOTICE / HINT NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Pre
SEE MORE:
IGB Signal Circuit Short to Auxiliary Battery (P1CFA12)
DESCRIPTION The hybrid vehicle control ECU monitors the IGB signal received from the certification ECU (smart key ECU assembly). When an error is detected in the IGB signal, this DTC is stored. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P1CFA12
Motor Electronics Coolant Pump "A" No Signal (P314A31)
DESCRIPTION Refer to the description for DTC P0C7396. Click here The inverter water pump assembly sends the inverter water pump speed (measured value) signal to the hybrid vehicle control ECU. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P314A31
