Lexus ES manuals

Lexus ES: Slave Module Horizontal Axis Misalignment (C1AC2)

DESCRIPTION

This DTC is stored when the angle of the blind spot monitor sensor LH deviates more than the allowable range from the horizontal axis.

HINT:

  • If a drum tester such as a speedometer tester, brake/speedometer combination tester or chassis dynamometer is used with the blind spot monitor system on, the blind spot monitor sensor may store this DTC by mistake.
  • When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AC2

Slave Module Horizontal Axis Misalignment

When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is activated

Blind spot monitor sensor LH

CAUTION / NOTICE / HINT

NOTICE:

  • When checking for DTCs, make sure that the blind spot monitor system is turned on.
  • If the bumper is damaged or the vehicle has a history of body repair, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor sensor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

    Click here

    If the results are not as specified, it is possible that the blind spot monitor sensor installation area (frame, stud bolt) is deformed, so make corrections as necessary.

PROCEDURE

1.

CHECK VEHICLE CONDITION

(a) Check the condition of the rear bumper around the blind spot monitor sensors.

HINT:

When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.

Result

Proceed to

A sticker, mud, snow, ice, etc. is covering the sensor or surrounding area on the rear bumper.

A

There are scratches or dents on the rear bumper around the sensors.

B

No abnormalities.

B

GO TO STEP 3

A

2.

PERFORM BEAM AXIS CONFIRMATION

(a) Clean the rear bumper.

(b) Perform Blind Spot Monitor Beam Axis Confirmation using the Techstream.

Click here

Body Electrical > Blind Spot Monitor Slave > Utility

Tester Display

BSM Slave Beam Axis Display

Body Electrical > Blind Spot Monitor Slave > Utility

Tester Display

BSM Slave Beam Axis Adjustment

OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR LH

3.

CHECK INSTALLATION CONDITION

(a) Check the installation condition of the blind spot monitor sensor LH.

Click here

HINT:

Take the appropriate action in accordance with the result.

NEXT

4.

PERFORM BEAM AXIS CONFIRMATION

(a) Install the rear bumper.

for Single Type: Click here

for Dual Type: Click here

(b) Perform Blind Spot Monitor Beam Axis Confirmation using the Techstream.

Click here

Body Electrical > Blind Spot Monitor Slave > Utility

Tester Display

BSM Slave Beam Axis Display

Body Electrical > Blind Spot Monitor Slave > Utility

Tester Display

BSM Slave Beam Axis Adjustment

OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR LH

READ NEXT:

 Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZE BLIND SPOT MONITOR SYSTEM (a) Customizing with the Techstream NOTICE: When the customer requests a change in a function, first make sure that the function can be cust

 Customize Parameters

CUSTOMIZE PARAMETERS CUSTOMIZE BLIND SPOT MONITOR SYSTEM (a) Customizing with the Techstream NOTICE: When the customer requests a change in a function, first make sure that the function can be cust

 Data List / Active Test

DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a pa

SEE MORE:

 Front Camera Response Malfunction (C2A6D)

DESCRIPTION During self diagnosis of the parking assist ECU, the parking assist ECU sends display mode ID signals to the front television camera assembly. This DTC is stored when the output of the front television camera assembly does not match the expected output. DTC No. Detection Item DTC

 Removal

REMOVAL PROCEDURE 1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT Click here 2. REMOVE SPARE WHEEL COVER TRAY Click here 3. REMOVE REAR FLOOR FINISH PLATE Click here 4. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH Click here 5. REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER LH Click here 6. REMOVE FUEL F

© 2016-2024 Copyright www.lexguide.net