Lexus ES: Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range (B26031C)
DESCRIPTION
Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B26031C | Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range | When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU. |
|
WIRING DIAGRAM
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM (TILT MANUAL SWITCH UP/DOWN, TELESCOPIC MANUAL SWITCH SHORT/LONG) |
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Turn the Techstream on.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Tilt&Telescopic > Data List| Tester Display |
|---|
| Tilt Manual Switch Up |
| Tilt Manual Switch Down |
| Telescopic Manual Switch Short |
| Telescopic Manual Switch Long |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tilt Manual Switch Up | Input state of tilt up switch | OFF or ON | - | - |
| Tilt Manual Switch Down | Input state of tilt down switch | OFF or ON | - | - |
| Telescopic Manual Switch Short | Input state of telescopic contract switch | OFF or ON | - | - |
| Telescopic Manual Switch Long | Input state of telescopic extend switch | OFF or ON | - | - |
OK:
The value of each Data List item changes in accordance with the operation of the switch.
| NG | .gif) | GO TO STEP 3 |
|
.gif)
| 2. | CONFIRM DTC |
(a) Clear the DTCs.
Body Electrical > Tilt&Telescopic > Clear DTCs(b) Check for DTCs.
Body Electrical > Tilt&Telescopic > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
| A | | REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
| B | | USE SIMULATION METHOD TO CHECK |
| 3. | CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH) |
(a) Disconnect the G63 multiplex tilt and telescopic ECU connector.
(b) Disconnect the G31 tilt and telescopic switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-5 (VC) - G31-1 (VC) | Always | Below 1 Ω |
| G63-18 (MSW) - G31-3 (MSW) | Always | Below 1 Ω |
| G63-5 (VC) or G31-1 (VC) - Body ground | Always | 10 kΩ or higher |
| G63-18 (MSW) or G31-3 (MSW) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 4. | CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE) |
| (a) Reconnect the G63 multiplex tilt and telescopic ECU connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-5 (VC) - G63-18 (MSW) | Engine switch on (IG) | 4.9 to 5.1 V |
| NG | | REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
|
| 5. | INSPECT TILT AND TELESCOPIC SWITCH |
| (a) Remove the tilt and telescopic switch. Click here |
|
.gif)
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G31-1 (VC) - G31-3 (MSW) | Tilt up | 342 to 378 Ω |
| Tilt down | 1890.5 to 2089.5 Ω | |
| Telescopic contract | 750.5 to 829.5 Ω | |
| Telescopic extend | 152 to 168 Ω |
| OK | | REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
| NG | | REPLACE TILT AND TELESCOPIC SWITCH |
READ NEXT:
Tilt Position Sensor or Tilt Motor Circuit Component Internal Failure (B261096)
DESCRIPTION The tilt motor (steering column assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt po
Telescopic Position Sensor or Telescopic Motor Circuit Component Internal Failure (B261196)
DESCRIPTION The telescopic motor (steering column assembly) is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column assembly forward
ECU Power Source Circuit System Voltage Low (B2620A2)
DESCRIPTION The ECU power source circuit supplies positive (+) voltage to the multiplex tilt and telescopic ECU. DTC No. Detection Item DTC Detection Condition Trouble Area B2620A2 ECU
SEE MORE:
Open Circuit in Main Relay 1 (C1311,C1312)
DESCRIPTION The main relay supplies power to the switching solenoid and the linear solenoid. The main relay remains on for approximately 2 minutes after the power switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.
Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during flow shutting valve (water by-pass hose assembly) removal/installation are shown below. Necessary Proced
