Lexus ES manuals

Lexus ES: Power Mirrors do not Return to Memorized Position

DESCRIPTION

If any of the M1, M2 or M3 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. The main body ECU (multiplex network body ECU) sends the reproduction signal to each outer mirror control ECU assembly via CAN communication. When receiving the reproduction signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly, to adjust the mirror surface to the stored position.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here

PROCEDURE

1.

CHECK SEAT MEMORY SWITCH FUNCTION

(a) When any seat memory switch (M1, M2 or M3) is pressed, check that the driver seat moves to the memorized position.

Click here

OK:

Driver seat moves to the memorized position.

NG

GO TO FRONT POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

OK

2.

CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION

(a) Check the electrical remote control mirror function.

Click here

OK:

Electrical remote control mirror function is normal.

NG

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror cannot be Adjusted with Power Mirror Switch)

OK

3.

READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Mirror L or Mirror R / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Mirror L > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Mirror Memory No.1

Mirror position memorized in memory switch M1

OFF or ON

OFF: Not memorized

ON: Memorized

-

Mirror Memory No.2

Mirror position memorized in memory switch M2

OFF or ON

OFF: Not memorized

ON: Memorized

-

Mirror Memory No.3

Mirror position memorized in memory switch M3

OFF or ON

OFF: Not memorized

ON: Memorized

-

Body Electrical > Mirror L > Data List

Tester Display

Mirror Memory No.1

Mirror Memory No.2

Mirror Memory No.3

Body Electrical > Mirror R > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Mirror Memory No.1

Mirror position memorized in memory switch M1

OFF or ON

OFF: Not memorized

ON: Memorized

-

Mirror Memory No.2

Mirror position memorized in memory switch M2

OFF or ON

OFF: Not memorized

ON: Memorized

-

Mirror Memory No.3

Mirror position memorized in memory switch M3

OFF or ON

OFF: Not memorized

ON: Memorized

-

Body Electrical > Mirror R > Data List

Tester Display

Mirror Memory No.1

Mirror Memory No.2

Mirror Memory No.3

OK:

ON (Memorized) appears on the screen.

NG

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror Surface Position is not Memorized)

OK

4.

CHECK MEMORY AND REACTIVATION FUNCTION

(a) Turn the power switch on (IG).

*a

Turn to Fully Left Position

(b) Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

(c) Press the M1 switch while the SET switch is being pressed.

(d) Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

(e) Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

(f) Press the M1 switch.

(g) Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

Result

Proceed to

Memory and reactivation functions on both mirrors are not normal

A

Memory and reactivation function on driver door mirror is not normal

B

Memory and reactivation function on front passenger door mirror is not normal

C

A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

GO TO STEP 7

B

5.

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

(a) Temporarily replace the outer rear view mirror assembly (driver door) with a new or known good one.

Click here

NEXT

6.

CHECK MEMORY AND REACTIVATION FUNCTION

(a) Turn the power switch on (IG).

*a

Turn to Fully Left Position

(b) Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

(c) Press the M1 switch while the SET switch is being pressed.

(d) Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

(e) Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

(f) Press the M1 switch.

(g) Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

7.

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)

(a) Temporarily replace the outer rear view mirror assembly (front passenger door) with a new or known good one.

Click here

NEXT

8.

CHECK MEMORY AND REACTIVATION FUNCTION

(a) Turn the power switch on (IG).

*a

Turn to Fully Left Position

(b) Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

(c) Press the M1 switch while the SET switch is being pressed.

(d) Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

(e) Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

(f) Press the M1 switch.

(g) Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

READ NEXT:

 Reverse Shift-linked Function of Power Mirrors does not Operate

DESCRIPTION The ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU)

 Power Mirror Control System (for Hv Model Without Memory)

 Precaution

PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following s

SEE MORE:

 Removal

REMOVAL PROCEDURE 1. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY Click here 2. REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY Click here 3. REMOVE UNION TO CHECK VALVE HOSE (a) Disengage the clamp to separate the union to check valve hose from the air tube.

 Generator Mechanical Linkage Failure (P1C8779,P1C8879)

DTC SUMMARY Refer to the DTC summary for DTC P1C7779. Click here DESCRIPTION Refer to the description for DTC P1C7779. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P1C8779 Generator Mechanical Linkage Failure Generator (MG1) loc

© 2016-2024 Copyright www.lexguide.net