Lexus ES: Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Signal Invalid (P060629)
DESCRIPTION
The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
P060629 | Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Signal Invalid | ECU internal malfunction (1 trip detection logic) | Battery ECU assembly | Comes on | Master Warning Light: Comes on |
MONITOR DESCRIPTION
The battery ECU assembly monitors its internal operation. If the internal operation is malfunctioning, the battery ECU assembly illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs | P0606 (INF P060629): Control module processor (battery energy control module) |
Required sensors/components | Battery ECU assembly |
Frequency of operation | Continuous |
Duration | TMC's intellectual property |
MIL operation | Immediately |
Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property | - |
COMPONENT OPERATING RANGE
Battery ECU assembly | DTC P0606 (INF P060629) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the power switch on (IG) and turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the power switch off and wait for 2 minutes or more.
-
Turn the power switch on (IG) and turn the Techstream on.
-
With power switch on (IG) and wait for 30 seconds or more.[*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
-
Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
1. | REPLACE BATTERY ECU ASSEMBLY |
Click here
NEXT | | END |
READ NEXT:
DESCRIPTION The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble
DESCRIPTION The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble
DESCRIPTION The battery ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble
SEE MORE:
INSPECTION CAUTION / NOTICE / HINT CAUTION: Be careful so that fingers and clothing do not get caught in the moving parts when performing this test. PROCEDURE 1. INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (a) Check the HI operation. (1) Connect a positive (+) lead from the auxiliary battery to termi
COMPONENTS ILLUSTRATION *1 IGNITION COIL ASSEMBLY *2 ENGINE WIRE *3 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY *4 CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY *5 CYLINDER HEAD COVER SUB-ASSEMBLY *6 SPARK PLUG TUBE GASKET *7 CAMSHAFT POSITION SENSOR (for Intake Side)
© 2016-2024 Copyright www.lexguide.net