DTC SUMMARY
MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects an open circuit malfunction.
HINT:
The cause of this malfunction may be one of the following:
DESCRIPTION
Refer to the description for DTC P0AE411.
Click here
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1C8449 | High Voltage Power Resource Circuit Short during Ready ON | High-voltage circuit malfunctions between the HV battery and inverter with converter assembly. The voltage before boosting continues to be out of the HV battery voltage range or the integrated value of variation amount of the voltage before boosting for a specified period of time is large while the power switch is on (READY). The EV electric battery fuse in the service plug grip is blown, the service plug grip is removed, SMRB or SMRG remains open, or the high-voltage cable has an open circuit. (1 trip detection logic) |
| Comes on | Master Warning Light: Comes on |
| DTC No. | Data List |
|---|---|
| P1C8449 |
|
The following items can be helpful when performing repairs:
MONITOR DESCRIPTION
A malfunction is detected and the MIL is illuminated when the following condition is met:
A large fluctuation of DC/DC converter voltage is occurred due to power cable disconnection.
MONITOR STRATEGY
| Related DTCs | P3004 (INF P1C8449): Power Cable Malfunction |
| Required sensors/components | DC/DC converter, HV battery |
| Frequency of operation | - |
| Duration | TMC's intellectual property |
| MIL operation | 1 driving cycle |
| Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
| TMC's intellectual property | - |
COMPONENT OPERATING RANGE
| Hybrid vehicle control ECU | P3004 (INF P1C8449) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
Click here
Click here
HINT:
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
HINT:
WIRING DIAGRAM
Refer to the wiring diagram for the HV battery high-voltage line circuit.
Click here
CAUTION / NOTICE / HINT
CAUTION:
Click here
HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
| *a | Without waiting for 10 minutes |
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
PROCEDURE
| 1. | CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control, Motor Generator and HV Battery / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes Powertrain > Motor Generator > Trouble Codes Powertrain > HV Battery > Trouble Codes| Result | Proceed to |
|---|---|
| P1C8449 only is output, or P0A9563 and DTCs except the ones in the table below are also output. | A |
| DTCs of hybrid control system in the tables below are output. | B |
| DTCs of motor generator control system in the tables below are output. | C |
| DTCs of hybrid battery system in the tables below are output. | D |
| P0A9563 is also output. | E |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Hybrid control system | P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure |
| P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure | ||
| Motor generator control system | P0A1B1F | Generator Control Module Circuit Intermittent | |
| P0A1A47 | Generator Control Module Watchdog / Safety μC Failure | ||
| P0A1A49 | Generator Control Module Internal Electronic Failure | ||
| P1C2A1C | Generator A/D Converter Circuit Circuit Voltage Out of Range | ||
| P1C2A49 | Generator A/D Converter Circuit Internal Electronic Failure | ||
| P313383 | Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect | ||
| P313386 | Communication Error from Generator to Drive Motor "A" Signal Invalid | ||
| Hybrid battery system | P060687 | Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message | |
| P060A47 | Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure | ||
| P060A87 | Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message | ||
| P060B16 | Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold | ||
| P060B49 | Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure | ||
| Power source circuit malfunction | Motor generator control system | P06D61C | Generator Control Module Offset Power Circuit Voltage Out of Range |
| Hybrid battery system | P1CBB12 | Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery | |
| P1CBB14 | Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open | ||
| Communication system malfunction | Hybrid control system | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| U011187 | Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message | ||
| Motor generator control system | P313387 | Communication Error from Generator to Drive Motor "A" Missing Message | |
| Sensor and actuator circuit malfunction | Hybrid control system | P0ABF00 | Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance |
| P0AD911 | Hybrid/EV Battery Positive Contactor Circuit Short to Ground | ||
| P0AD915 | Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open | ||
| P0ADD11 | Hybrid/EV Battery Negative Contactor Circuit Short to Ground | ||
| P0ADD15 | Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open | ||
| Motor generator control system | P0D2D16 | Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold | |
| P0D2D17 | Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold | ||
| Hybrid battery system | P0ABF11 | Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground | |
| P0ABF15 | Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open | ||
| P0ABF28 | Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure | ||
| P0ABF2A | Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range | ||
| P0B0E11 | Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground | ||
| P0B0E15 | Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open | ||
| P0B1362 | Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure | ||
| System malfunction | Hybrid control system | P0A1F94 | Hybrid/EV Battery Energy Control Module Unexpected Operation |
| P0D2D1C | Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range | ||
| P0E311C | Boosting Converter Voltage Sensor "A" Voltage Out of Range | ||
| P1C8349 | High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction | ||
| P300449 | High Voltage Power Resource Circuit Short during Pre-Charge | ||
| Motor generator control system | P1CB69E | Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On | |
| P0CA300 | DC/DC Converter Step Up Voltage Performance | ||
HINT:
(e) Turn the power switch off.
| B | | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
| C | | GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM) |
| D | | GO TO DTC CHART (HYBRID BATTERY SYSTEM) |
| E | | GO TO DTC CHART (P0A9563) |
|
| 2. | CLEAR DTC |
Click here
|
| 3. | CHECK DTC OUTPUT (HYBRID CONTROL, HV BATTERY) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control and HV Battery / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes Powertrain > HV Battery > Trouble Codes| Result | Proceed to |
|---|---|
| P1C8449 only is output, or DTCs except the ones in the table below are also output. | A |
| DTCs of hybrid control system in the tables below are output. | B |
| DTCs of hybrid battery system in the tables below are output. | C |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| System malfunction | Hybrid control system | P1AC413 | Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open |
| Hybrid battery system | P1AC413 | Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open | |
| P1AC49E | Hybrid/EV Battery Stack 1 Current Interrupt Device Stuck On | ||
| P1AC513 | Hybrid/EV Battery Stack 2 Current Interrupt Device Circuit Open | ||
| P1AC59E | Hybrid/EV Battery Stack 2 Current Interrupt Device Stuck On | ||
HINT:
(e) Turn the power switch off.
| B | | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
| C | | GO TO DTC CHART (HYBRID BATTERY SYSTEM) |
|
| 4. | CHECK DTC OUTPUT (HYBRID CONTROL) |
(a) Connect the Techstream to the DLC3.
(b) With the vehicle stopped, apply the parking brake and turn the power switch on (READY).
HINT:
(c) Ensure the safety of the areas in front and at the back of the vehicle.
(d) Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.
HINT:
Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.
(e) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(f) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes| Result | Proceed to |
|---|---|
| P1C8449 is output, or no DTCs are output. | A |
| Power switch could not be turned on (READY) and DTC P300449 is output. | B |
(g) Turn the power switch off.
| B | | GO TO DTC CHART (P300449) |
|
| 5. | CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR) |
Click here
| NG | | CONNECT SECURELY |
|
| 6. | CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR) |
Click here
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
| B | | CONNECT SECURELY |
| C | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 7. | CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR) |
Click here
| NG | | CONNECT SECURELY |
|
| 8. | CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY) |
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the No. 1 HV battery cover panel RH.
Click here
(c) Disconnect the N22 HV battery junction block assembly connector.
(d) Disconnect the G59 hybrid vehicle control ECU connector.
| (e) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(f) Reconnect the G59 hybrid vehicle control ECU connector.
(g) Reconnect the N22 HV battery junction block assembly connector.
(h) Install the No. 1 HV battery cover panel RH.
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 9. | CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND) |
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the No. 1 HV battery cover panel RH.
Click here
(c) Disconnect the N22 HV battery junction block assembly connector.
| (d) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(e) Reconnect the N22 HV battery junction block assembly connector.
(f) Install the No. 1 HV battery cover panel RH.
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 10. | CHECK HV BATTERY |
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the electric vehicle battery plug assembly.
Click here
| (c) Disconnect the y11 and y12 HV battery high voltage connectors. |
|
| (d) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
(e) Reconnect the y11 and y12 HV battery high voltage connectors.
(f) Install the electric vehicle battery plug assembly.
| NG | | GO TO STEP 13 |
|
| 11. | REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY |
Click here
|
| 12. | CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION) |
CAUTION:
Be sure to wear insulated gloves.
(a) Install the service plug grip.
(b) Turn the power switch on (IG).
(c) Clear the DTCs.
Powertrain > Hybrid Control > Clear DTCs(d) Turn the power switch off and wait for 2 minutes or more.
(e) Turn the power switch on (READY).
(f) Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid/EV Battery Voltage, VL-Voltage before Boosting.
(g) According to the display on the Techstream, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.
Powertrain > Hybrid Control > Data List| Tester Display |
|---|
| VL-Voltage before Boosting |
| Hybrid/EV Battery Voltage |
| Result | Proceed to |
|---|---|
| Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. | A |
| Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. | B |
(h) Turn the power switch off.
| A | | END |
| B | | REPLACE HYBRID VEHICLE CONTROL ECU |
| 13. | REPLACE BATTERY ECU ASSEMBLY |
Click here
|
| 14. | SIMULATION TEST |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG) and turn the Techstream on.
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Clear the DTCs and freeze frame data.
Powertrain > Hybrid Control > Clear DTCs(e) Turn the power switch off and wait for 2 minutes or more.
(f) Turn the power switch on (IG) and wait for 2 minutes or more.
(g) Enter the following menus: Powertrain / Hybrid Control and HV Battery / Trouble Codes.
(h) Check if DTCs are output.
Powertrain > Hybrid Control > Trouble Codes Powertrain > HV Battery > Trouble Codes| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs of hybrid battery system are output. | B |
(i) Turn the power switch off.
| A | | END |
| B | | GO TO DTC CHART (HYBRID BATTERY SYSTEM) |
Transmission (Input) Mechanical Linkage Failure (P1C8679)
Generator Mechanical Linkage Failure (P1C8779,P1C8879)
PCU Interlock Circuit Open (P1CE213,P1CE292)
Lost Communication with Airbag System Control Module Signal Plausibility Failure (P310764)
Pressure Control Solenoid "H" Circuit Short to Battery (P281612)