Lexus ES: High Voltage Fuse Accumulated Load History (P0A9563)
DESCRIPTION
The hybrid vehicle control ECU estimates the thermal load of the high voltage fuse. If the accumulated thermal load exceeds the threshold, the hybrid vehicle control ECU will store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A9563 | High Voltage Fuse Accumulated Load History | Accumulated thermal load of the high voltage fuse estimated by the hybrid vehicle control ECU exceeds the threshold. (1 trip detection logic) | Hybrid battery terminal block | Does not come on | Master Warning Light: Does not come on |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here .gif)
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 5 seconds or more.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
CAUTION / NOTICE / HINT
HINT:
If the hybrid battery terminal block has been replaced, make sure to perform "High Voltage Fuse Accumulated Load History Reset" and then clear the DTCs.
PROCEDURE
| 1. | REPLACE HYBRID BATTERY TERMINAL BLOCK |
Click here
|
.gif)
| 2. | PERFORM UTILITY (HIGH VOLTAGE FUSE ACCUMULATED LOAD HISTORY RESET) |
Click here
|
| 3. | CLEAR DTC (HYBRID CONTROL) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Clear the DTCs and freeze frame data.
Powertrain > Hybrid Control > Clear DTCs(e) Turn the power switch off.
| NEXT | .gif) | END |
READ NEXT:
Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground (P0A9B11,P0A9B15,P0AC511,P0AC515,P0ACA11,P0ACA15)
DESCRIPTION The battery temperature sensors are provided at 3 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance w
Hybrid/EV Battery Temperature Sensor "A" Voltage Out of Range (P0A9B1C,P0AC51C,P0ACA1C)
DESCRIPTION These DTCs will be stored if the difference between the maximum and minimum output of each battery temperature sensors exceeds a certain amount and if the output of one battery temperature
Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range (P0A9B2A,P0AC52A,P0ACA2A,P306562)
DESCRIPTION Refer to the description for DTC P0A9B11. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0A9B2A Hybrid/EV Battery Tempera
SEE MORE:
Hybrid/EV Battery Voltage Isolation Sensor Circuit Internal Electronic Failure (P0AA749)
DESCRIPTION The hybrid vehicle control ECU monitors the insulation monitoring circuit located in the battery ECU assembly and detects malfunctions. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate P0AA749 Hybrid/EV Battery Voltage Isolation Sensor C
Installation
INSTALLATION PROCEDURE 1. INSTALL REAR SPOILER SUB-ASSEMBLY HINT: When installing a new rear spoiler sub-assembly, heat the luggage compartment door panel and rear spoiler sub-assembly using a heat light. Heating Temperature Item Temperature Luggage Compartment Door Panel 40 to 60°C (104
