Lexus ES: DC/DC Converter Temperature Sensor 2 Circuit Short to Ground (P0E5811,P0E5815)
DESCRIPTION
The motor generator control ECU (MG ECU), which is built into in the inverter with converter assembly, detects the temperature of the boost converter using the boost converter temperature sensor 2 (lower). The motor generator control ECU (MG ECU) also detects malfunctions in the boost converter temperature sensor 2 (lower) and its wiring.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0E5811 | DC/DC Converter Temperature Sensor 2 Circuit Short to Ground | Short to ground detected in boost converter temperature sensor 2 (lower) circuit (1 trip detection logic) | Inverter with converter assembly | Comes on | Master Warning Light: Comes on |
| P0E5815 | DC/DC Converter Temperature Sensor 2 Circuit Short to Battery or Open | Open or short to +B detected in boost converter temperature sensor 2 (lower) circuit (1 trip detection logic) | Inverter with converter assembly | Comes on | Master Warning Light: Comes on |
| DTC No. | Data List |
|---|---|
| P0E5811 P0E5815 | Boosting Converter Temperature 2 (Lower) |
MONITOR DESCRIPTION
If the motor generator control ECU detects a malfunction of the boost converter temperature sensor 2 (lower), it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
| Related DTCs | P0E5A (INF P0E5811): DC/DC Converter Temperature Sensor "C" Range Check P0E5B (INF P0E5815): DC/DC Converter Temperature Sensor "C" Range Check |
| Required sensors/components | Boost converter temperature sensor 2 (lower) |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | Immediately |
| Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
TYPICAL MALFUNCTION THRESHOLDS
| TMC's intellectual property | - |
COMPONENT OPERATING RANGE
| Motor generator control ECU | DTC P0E5A (INF P0E5811) is not detected DTC P0E5B (INF P0E5815) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
-
With power switch on (IG) and wait for 5 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
| 1. | REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS |
Click here
| NEXT | .gif) | COMPLETED |
READ NEXT:
DC/DC Converter Temperature Sensor 2 Circuit Voltage Out of Range (P0E581C)
DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that the boost converter temperature sensor 2 (lower) value is abnormal. The cause of this malfunction may be one of the following: Internal in
Generator Execution Torque Performance (P0E7100)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates that the generator torque execution value does not correspond to the torque command value from the hybrid vehicle control ECU to the generator (M
Motor Generator ECU(EEPROM) Calibration / Parameter Memory Failure (P1C2E46)
DESCRIPTION The motor generator control ECU monitors its internal operation and will store this DTC if it detects a malfunction in its EEPROM. DTC No. Detection Item DTC Detection Condition T
SEE MORE:
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the parking support brake system on. (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Trouble Codes. (f) Check fo
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspect
