Lexus ES manuals

Lexus ES: Actuator Supply Voltage "A" Stuck On (P06579E)

Lexus ES (XZ10) Service Manual / Engine & Hybrid System / 2gr-fks (engine Control) / Sfi System / Actuator Supply Voltage "A" Stuck On (P06579E)

MONITOR DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the engine switch is turned off. If the output voltage is 7 V or higher when the engine switch is turned off, the ECM illuminates the MIL and stores this DTC when the engine switch is turned on (IG).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P06579E

Actuator Supply Voltage "A" Stuck On

A throttle actuator power supply error (1 trip detection logic).

ECM

Comes on

DTC stored

SAE Code: P0657

MONITOR STRATEGY

Related DTCs

P0657: Electronic throttle actuator supply voltage circuit performance

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

Throttle actuator

Frequency of Operation

Once per driving cycle

Duration

1 second

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

Both of the following conditions are met

-

Battery voltage

8 V or higher

Command to electronic throttle actuator power

Off

TYPICAL MALFUNCTION THRESHOLDS

Electronic throttle actuator power supply voltage

7 V or higher

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the engine switch off.
  7. Disconnect the Techstream.
  8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) battery terminal.
  10. Turn the engine switch on (IG) [A].
  11. Wait 10 seconds or more.
  12. Turn the engine switch off [B].
  13. Wait 15 seconds or more.
  14. Connect the Techstream to the DLC3.
  15. Turn the engine switch on (IG).
  16. Turn the Techstream on.
  17. Wait 5 seconds or more [C].
  18. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  19. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  20. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  21. Input the DTC: P06579E.
  22. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
    • [A] to [D]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTC.

Powertrain > Engine > Clear DTCs

(e) Turn the engine switch off.

NEXT

2.

READ OUTPUT DTC (DTC P06579E)

(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the engine switch on (IG).

(d) Wait 10 seconds or more.

(e) Turn the engine switch off.

(f) Wait 15 seconds or more.

(g) Connect the Techstream to the DLC3.

(h) Turn the engine switch on (IG).

(i) Wait 5 seconds or more.

(j) Turn the Techstream on.

(k) Enter the following menus: Powertrain / Engine / Trouble Codes.

(l) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P06579E is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM

READ NEXT:

 Brake Switch "B" Circuit Short to Battery (P070312)

DESCRIPTION The stop light switch assembly is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is work

 Transmission Range Sensor "A" Circuit Open (P070513,P070562)

DESCRIPTION The park/neutral position switch assembly detects the shift position and sends signals to the ECM. DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Not

 Fuel Rail Pressure Sensor (Low) Circuit Short to Ground (P107A11)

DESCRIPTION The fuel pressure sensor (for low pressure side) replaces the fuel pressure with electrical signals and outputs them to the ECM. The ECM controls the optimal fuel pressure for the operati

SEE MORE:

 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure (P001107,P002107)

DESCRIPTION Refer to DTC P001013. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P001107 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure 10° CA or greater camshaft timing gear assembly (ban

 Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)

DESCRIPTION This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the navigation system vehicle customization screen. HINT: The certification ECU (smart key ECU assembly) controls the smart access system with push-button start (for Entry

© 2016-2024 Copyright www.lexguide.net